Preparing to Configure, Configuring | Siemens CP 243-2 manual

Technical Description and Installation Instructions

Note

Changing from the configuration mode to the protected mode is only possible when there is no slave with address ª0º connected to the AS-Interface. If a slave ª0º is connected, the ªSFº LED lights up when the SET button is pressed.

Preparing to Configure

Make sure that the following situation applies:

SThe S7-22x CPU must be set to STOP (PLC_RUN=0).

SThe CP 243-2 and all AS-i slaves must be connected to the AS-Interface and supplied with power by the AS-i power supply.

Configuring

1.Press the DISPLAY button to set the CP 243-2 display to the ªstatus displayº mode (initial status).

2.Check whether the CP 243-2 is in the ªconfiguration modeº. (ºCMº LED lit ). If not, change the CP 243-2 to the configuration mode using the SET button.

3.By changing to the slave display with the DISPLAY button, you can check whether all the slaves connected to the AS-Interface exist.

4.Press the SET button. The CP 243-2 is configured.

At the same time, the CP 243-2 is changed to the protected mode; the ªCMº LED goes off.

The ªCERº LED also goes off since following configuration, the ªexpected configurationº stored on the CP 243-2 matches the ªactual configurationº on the AS-Interface.

Note

Configuring the CP 243-2 during an AS-Interface Power Fail (for example when the AS-i power supply unit is turned off or when the CP 243-2 is not connected to the AS-Interface) resets the configuration of the CP 243-2. This has the following results:

SNo AS-i slaves are configured;

SAll AS-i slave parameters are set;

SAutomatic address programming is activated (bit AUTO_ADDRESS_ENABLE = 1).

SIMATIC NET CP 243-2 AS-i Master	1-17
C79000-G8976-C142/02

Image 25

Siemens CP 243-2 installation instructions Preparing to Configure, Configuring

Contents

Manual AS-Interface MasterAppendix 07/2000 C79000-G8976-C142 Release Qualified Personnel Safety GuidelinesCorrect Usage Trademarks Preface We recommend the following procedure whenPurpose of the Manual Requirements Preface Contents Command Interface Signaling Errors and Diagnostics in the User ProgramDealing with Problems / Error Displays References Simatic NET ± Support and Training Glossary Index Contents Technical Description and Installation Instructions General Notes on Operation ± Safety Warnings DP Slave and AS-i Master Uses of the ModuleAS-i Master Components Supplied Feature Technical Specifications of the ModuleExplanation/Values Slots in the S7-200 Installing the ModulePossible Restrictions Connection, Display and Control Elements Front Panel ± Access to all Functions Connections Terminal BlockConnections to the AS-i Cable Technical Description and Installation Instructions Standard Operation Modes of the CPExtended Operation Changing the Display Status ± Display Button Displays and Operator ControlsMeaning of the LEDs SET Button Interpreting the Status Display Status DisplayLED color Status LED color Status SF red System error Meaning Slave Display Characteristics of the Slave DisplayInterpreting the Slave Display Status Display Statuses in Detail Example of a Slave Display Example of a Slave Display Configuration Mode Configuring the AS-Interface with the SET ButtonProtected Mode Interpreting the Display Status Configuring Preparing to Configure Technical Description and Installation Instructions Interface to the User Program S7-200 CPU CP 243-2 as Expansion Module in the S7-200 OverviewS7-200 CPU Digital Module Analog Module Address Areas Addressing the CP 243-2 in the S7-200 CPUExamples CPU CPU 14 DI 10 do Example of a CPU 224, a CP 243-2 and a CP Module CPU 14DI 10 do Overview Meaning of the Data in the Digital Module Meaning Identification Register in the Digital ModuleRange of Values Example Example of Access to the Error Register Error Register in the Digital ModuleMeaning for the User Program Structure of the Status Byte Status Byte Input Register 8DIDescription of the Bits Bit Value Structure of the Control Byte Control Byte Output Register 8DOBit Value Meaning Digital module 8DI/8DO Meaning of the Data in the Analog Module Identification Register in the Analog Module Structure of the Error Register Error Register in the Analog ModuleBit Description/Range of Values Example of Access to the Error Register Access in the User Program Access to the Analog Input and Output WordsPrinciple Advantage Interface to the User Program in the S7-200 CPU Assignment of the Input Areas Analog Input AreaS7-200 CPU Banks 2±15 Response data on the AS-Interface Bank 1 Diagnostics on the AS-InterfaceBanks 16±30 Reserved area Bank 31 Binary input data of the AS-i slaves 1B ± 31B Banks 48±63 Reserved area Banks 32±47 Analog input data of the AS-i slaves Assignment of the Output Areas Analog Output AreaBank 1 reserved Bank 31 Binary output data of the AS-i slaves 1B ± 31B Banks 2±15 Command data on the AS-InterfaceBanks 32±47 Analog output data of the AS-i slaves Access to the Data of the AS-i Slaves Access to the Binary Values Bit 7±4 Bit 3±0 Bank Byte no Reserved Slave 1B Special Feature of Analog Slaves Data Exchange in the Stop Mode of the S7-22x CPU Output byte AS-i slaves Data Access with Micro Access to the AS-i User Data Assignment of the AS-i Analog Data Access to the Analog ValuesBank Byte no Meaning Simatic NET CP 243-2 AS-i Master C79000-G8976-C142/02 Access to the Data of the AS-i Slaves Access to the Data of the AS-i Slaves Access to the Data of the AS-i Slaves Access to the Data of the AS-i Slaves Special Situations Representation of the Analog Values SBR 4 STL Access to the AS-i Analog Data Access to the Data of the AS-i Slaves Signaling Errors and Diagnostics User Program Error Signaling Signaling STL Example Example Reading the Delta List Signaling Errors and Diagnostics in the User Program Command Interface Command Buffer and Response Buffer Command interface of the CP AS-i master User program Reaction to command Command Sequence SBR 3 STL Example Q1.0 Select bank AIW0, VW512 Name Description of the AS-i CommandsParameter Return LPF Bank Byte Meaning / Content General Structure of the Command Buffer Bank Byte General Structure of the Response Buffer Command Status Bit Slave address General Structure of the AS-i Slave Address Purpose SetPermanentParameterStructure of the Job Data in the Send Buffer Structure of the Job Data in the Receive Buffer GetPermanentParameter WriteParameter Purpose of the Command ReadParameter StoreActualParameters ID code SetExtendedPermanentConfigurationExtended ID2 code GetExtendedPermanentConfiguration StoreActualConfiguration GetExtendedActualConfiguration SetExtendedLPS SetOfflineMode Reserved Mode SelectAutoprogramming SetOperationMode ChangeAS-iSlaveAddress End bit error detected Parity error detected Error detectedRead error in non-volatile memory GetAS-iSlaveStatus Reserved GetLPS, GetLAS, GetLDS, GetFlags Bit Number Meaning Flag Meaning of the Flags GetExtendedTotalConfiguration Idcode slave Ext ID1 slave Command Interface Command Interface Reserved Parameter slave 1B StoreExtendedTotalConfiguration Idcode slave Ext ID1 Slave Configuration slave Ext ID2 slave Command Interface Command Interface Configmode Autoaddrenable Echo of the command number 3A H Command status WriteExtendedParameterList Echo of the command number 3C H Command status ReadExtendedParameterEchoList Command Interface Purpose ReadVersionID Reserved ID code ReadAS-iSlaveID Reserved Extended ID1 code ReadAS-iSlaveID1 Irrelevant Extended ID1 code WriteAS-iSlaveExtendedID1 Reserved Slave ID2 ReadAS-iSlaveID2 ReadAS-iSlaveI/O Reserved Configuration GetLPF WriteAS-iSlaveParameterString Byte Meaning ReadAS-iSlaveParameterString ReadAS-iSlaveIDString ReadAS-iSlaveDiagnosticString ReadDataandDeltaList Structure of the Command BufferStructure of the Response Buffer Delta Slave Reserv Slave 7B Slave 6B Command Interface Dealing with Problems / Error Displays Detecting Defective AS-Interface Slaves Simple Replacement of AS-Interface SlavesYou can now replace the defective slave as follows Error Error Displays of the CP 243-2 / Remedying ErrorsPossible Cause Remedy Error Possible Cause Remedy Dealing with Problems / Error Displays Dealing with Problems / Error Displays List of Master Functions Available Pics for the CPComment / Function implemented by / Section Function or Call on the Host Interface AS-Interface Protocol Implementation Idcod AS-Interface Protocol Implementation Simatic S7-200 References References Order numbers Product Name Installation InstructionsEU Directive EMC 89/336/EEC Area of Application Simatic NET CP 243-2 AS-i Master C79000-G8976-C142/02 Simatic Training Center Simatic NET ± Support and TrainingSimatic Customer Support Hotline Nuremberg Johnson City Singapore Simatic Basic Hotline Further Support Simatic Customer Support Online ServicesSimatic Premium Hotline Glossary AS-i slave AS-i moduleAS-i standard slave Extended AS-i master Standard AS-i master Nibble Glossary-4 Index PICS, A-1