Mounting, Crimp Terminals | Sierra Wireless DART 300 instruction

User’s Guide

Considerations

11.3.3.Crimp Terminals

If suitable terminal connection points are available on the vehicle for power connection then the use of crimp terminals is encouraged:

•When using crimp terminals, do not leave bare wire exposed.

•Do not use crimp terminals for more than one wire unless it is designed for this.

11.4.Mounting

The DART modem should be secured in all installations to prevent movement and possible damage to, or loss of, connections. Any orientation is acceptable but laying flat with the case screws on the bottom is recommended. An optional mounting bracket is available from Sierra Wireless. Refer to Figure 11-1 for instructions for installing the DART 300 with the optional mounting bracket (part number 6000055).

Figure 11-1: DART Mounting Bracket.

2110212 Rev 1.0

Page 95

Image 106

Sierra Wireless DART 300 manual Mounting, Crimp Terminals, User’s Guide Considerations

Contents

Sierra Wireless Dart 300 Cdpd Modem 2110212 Rev November Patents Safety and HazardsImportant Notice Copyright Regulatory Information RSA Licensee Contact Information Dart 300 Modem User’s Guide 2110212 Rev Contents Introduction Feature Reference Cdpd Network Registration Protocols and Packet Assembly Features Transmission Control Protocol TCP Configuration and Use Intstallation References Installation ConsiderationsAT Commands and Status Registers 119 Specifications 123 Introduction How to ProceedAbout this Guide Focus List Document Structure Book 2 Feature ReferenceBook 3 Configuration and Use Introduction Dart 300 Modem User’s Guide About This Guide Dart 300 ChecklistBook 4 Installation Book 5 References Conventions Used in this Reference ReferencesCurrency Dart 300 / SB300 Dart Introduction Dart 300 Modem 2110212 Rev System Overview Typical System View Field Network Connection Client / Server Project StagesCentral Monitor Stage 1 Application Planning Stage 3 Field Installation and Testing Stage 2 Bench Integration and TestingStage 4 Rollout Service Activation Getting Started Antenna Power SupplySet-up Considerations Serial Cable Connections Cdpd ConfigurationUser’s Guide Getting Started Cdpd Network Registration Verifying Network Registration Ping Obtaining a Ping from the Modem Modem Modes and States Local DTE/DCE InterfaceModes Conditions Command to Data StateStates Sessions User’s Guide Local DTE/DCE Interface Data to Command StateDetails Data Buffers Command BufferModem Buffers Speed Buffering Parameters AT Command Handling and DefaultsGeneral Notes Responses and Results Returned by the Modem Framing Characters FramingResponses Response Framing Echo Verbose Quiet For Commands without a ResponseResult Codes Result Framing No Response Echo Verbose Quiet Possible Result Codes For Commands with a ResponseRegisters Result Framing After Response Echo Verbose Quiet Fixed Rate Setting +IPR RS-232C Interface and Control SignalsInterface Settings Flow Control DTR Flow Control Control SignalsData Terminal Ready DTR Request to Send RTS Ring Indicator RIData Set Ready DSR Clear to Send CTS Data Carrier Detect DCD DCD Product Features Friends Only Dial Directory Implementation User’s Guide Product Features Auto-dial on Start-up Sleep Mode Cdpd Sleep Logic Sleep Logic Deep Sleep Using Ring Indicator RI with Host SleepTo force re-registration now UDP/TCP Cdpd Radio and Booster Support Upgradability Communication Protocols and Stacks Protocols and Packet Assembly FeaturesOSI Model User Datagram Protocol UDP Packet Service ModesDart 300 Internal Protocol Stacks Answering UDP Server Sessions UDP Server FeaturesUser’s Guide Protocols and Packet Assembly Features UDP Server Receive Lock Disabling the UDP Server UDP Client Features Closing UDP Sessions Broadcast Configuration and UseUDP Broadcast and Multicast Multicast TCP Handshaking TCP Server FeaturesTransmission Control Protocol TCP Answering TCP Server Sessions Closing a TCP Session TCP Client FeaturesDisabling the TCP Server Serial Line Interface Protocol Slip TCP and Sleep ModePoint-to-Point Protocol PPP Forwarding a Packet Packet Assembly ManagementAssembling a Packet Local Echo Escaping Data State Time Dependent Escape Sequence Tdes Guard Time Important RelationshipsEscape Character Time Independent Escape Sequence Ties DTR Transition PAD Session TimeoutData and Telemetry Considerations TCP Remote Disconnect User’s Guide Protocols and Packet Assembly Features Feature Reference Dart 300 Modem 2110212 Rev Advanced Features Multiple Cdpd Accounts Channel Acquisition Controlling Network RegistrationChannel Scanning Spni Matching User’s Guide Advanced FeaturesSide Preference Assign a Channel Enable Spni Matching Spni Table ConfigurationDisable Spni Matching Determining Channel Acquisition Status Registration Active and Auto-register NEI Indices Manual Registration Automatic RegistrationDetermining Registration Status De-registration +WPNEILIST Radio Signal Monitors LED IndicatorMonitoring the Network Connection Registration Mode Registration Status Feature Reference Dart 300 Modem 2110212 Rev Configuration Checklist for UDP/TCP Service UDP/TCP ServiceNEI and Channel Restrictions Service Options Registration and Sleep ModeConfiguration and Use Dart 300 Modem User’s Guide UDP/TCP Service Packet Assembly and Forwarding OptionsEscape Options Server Sessions Using UDP/TCP ServiceSave Configuration Server Initialization Opening a UDP Server Session Using an Open UDP SessionUDP Server Sessions Receiving Data Closing UDP Server Sessions TCP Server SessionsTransmitting Data Opening a TCP Server Session Using an Open TCP Session No Carrier result Client SessionsClosing TCP Server Sessions UDP Client Connection By +WS198 TCP Client Connection Using a Client Session Closing a Client Session Cabling Sample UDP/TCP ConfigurationsCase 1 Semi-intelligent RTU DCE male Modem Configuration Protocol Considerations Case 2 Dumb Meter+IPR=9600 +WS212=0 Sample Configuration Meter Command Remarks +WPNEI= ip+WS179=0 +WS213=1 Using This Configuration Configuration and Use Dart 300 Modem 2110212 Rev SLIP/PPP Service Configuring Slip Service Configuration and Use Dart 300 Modem Receiving Using Slip ServiceTransmitting Escaping Data State Point to Point Protocol PPP Configuring PPP ServiceUsing DTR to Escape Closing a Slip Session User’s Guide SLIP/PPP Service Using PPP Service Closing a PPP Session User’s Guide SLIP/PPP Service Configuration and Use Dart 300 Modem 2110212 Rev Device Attachment Antenna Connection Watt Class I Booster Operation Installation Dart 300 ModemConnection Null-Modem Connection Serial ConnectorPin Signal Direction User’s Guide Device Attachment DCE modem Cable LengthDCE host Power Connection Installation Dart 300 Modem 2110212 Rev Temperature vs. Duty Cycle Installation ConsiderationsTemperature and Auto Shutdown Minutes Time Ambient Temperature C Wire Splicing AccessPower Supply Grounding Crimp Terminals MountingUser’s Guide Considerations Installation Dart 300 Modem 2110212 Rev 1AT Commands in Cdpd Mode Command Description AT Commands and Status RegistersAT Command Set AT+++ References Dart 300 Modem AT Commands in Cdpd Mode Command Description 0xC0Result Codes AT Commands in Cdpd Mode Description Options User’s Guide AT Command ReferenceOptions AT Commands in Cdpd Mode Sn=x Quiet Result Code Display OptionFraming of responses. See .3.3 for details Sn? AT Commands in Cdpd Mode Command Description AT & Commands in Cdpd Mode Description AT + Commands in Cdpd Mode Command Description +IPR=n AT + Commands in Cdpd Mode Command Description Change c.c.c.c to n.n.n.n? +WPSPNI= n,n,...n +WSn? Change c.c.c.c.q to n.n.n.n.p? Cdpd Status Registers Registers in Cdpd ModeS-Registers in Cdpd Mode Description Range Default Units Auto-answer Off DisabledWord PAD Packet Service DTE side stack WS-Registers in Cdpd ModeWS-Registers in Cdpd Mode Description Range Default Units Logic Sleep References Dart 300 Modem PAD Inter-Character Timer 174 175 User’s Guide AT Command Reference 209 201210 216 217 Important Notes and Dependencies +WS197, also setting +WS176=+WS197Result Codes in Cdpd Mode Verbose Meaning Result Codes Stored Profile Settings for Cdpd Mode References Dart 300 Modem 2110212 Rev General Communication Problems TroubleshootingProblem Description Suggestions Error # General Modem ProblemsReferencesDART 300 Modem Warranty Registration Cdpd Network / Connectivity ProblemsWarranty User’s Guide Troubleshooting Obtaining Service Radio Specifications SpecificationsPower Specifications Power Connector Regulatory Approvals Antenna SpecificationsAntenna Specifications FCC User’s GuideSpecifications Environmental SpecificationsApplication Interface Specifications Environmental Specifications