Prevent Allow Medium Removal 1Eh | Sony SDX-800V/R specification

6.Command Specification

PREVENT ALLOW MEDIUM REMOVAL

6.11.PREVENT ALLOW MEDIUM REMOVAL 1Eh

Bit	7	6	5	4		3	2	1	0
Byte
0				Operation	Code (1Eh)
1		Obsolete					Reserved
2				Reserved
3				Reserved
4				Reserved					Prevent
5				Control

The PREVENT ALLOW MEDIUM REMOVAL command requests that the target enable or disable the removal of the medium in the drive. This mechanism is independent of device reservations and the drive shall not allow medium removal if any initiator currently has medium removal prevented.

The prevention of medium removal shall begin when any initiator issues a PREVENT ALLOW MEDIUM REMOVAL command with a prevent bit of one (medium removal prevented). The prevention of medium removal for the logical unit shall terminate:

1.Upon a hard RESET condition.

2.Upon the receipt of a BUS DEVICE RESET message from any initiator

3.After all initiators that have medium removal prevented issue PREVENT ALLOW MEDIUM REMOVAL commands with a prevent bit of ZERO, and the target has successfully performed a synchronize cache operation.

While a prevention of medium removal condition is in effect the target shall inhibit mechanisms that normally allow removal of the medium by an operator.

Prevent: When this bit is set, the drive will not eject the tape following an UNLOAD. When it receives the UNLOAD, the drive writes any buffered data to tape, rewind, then unthreads the tape from the mechanism. The drive does not eject the tape. Setting this bit also completely disables the Eject button on the front panel (except emergency eject). This situation remains until the Prevent bit is set to ZERO.

When this bit is set to ZERO, the drive ejects the cassette following completion of an UNLOAD. The Eject button is also re-enabled.

6-64	SONY AIT-3Ex drive SDX-800V series Ver.1.1

Image 122

Sony SDX-800V/R manual Prevent Allow Medium Removal 1Eh, Obsolete Reserved Prevent Control

Contents

SDX-800V SDX-800V/R 5.25Model March Sony Business Europe Electronics Devices Marketing Singapore Changing List ESD EMC This page intentionally left blank Specifications Introduction Operation InstallationInstallation Guide Summary of LED Indications Operator Action Command Specification Scsi Interface Space 11h Mode Select 6/10 15h and 55hMode Sense 6/10 1Ah and 5Ah Test Unit Ready 00h Appendix F AIT based Worm system Drive DiagnosticsAppendix G Disaster Recover 14.6 Reset Handling Appendix H Glossary Introducing the Sony AIT Technology About this Product Specification ManualFeatures of the Drive Introduction How to get ECMA-222, 246, 291, 292, 329 Standard Document Reference This page intentionally left blank Specifications Dimensions Dimensions SDX-800V Mounting Holes 2a SDX-800V Mounting Holes 2b SDX-800V/R Mounting Holes Environmental Specifications WeightConnectors Temperature and Humidity Range Vibration AltitudeSuspended Particulate Shock Performance Specification Data Capacity Sustained Data Transfer Rate to and from the Tape Data transfer RateInitialize Time Burst Transfer Rate to and from the Scsi Bus Unload Time Error RateLoad Time Search Time Mean Time Between Failures Retry Limits on RewritesDefinition of Failure Mean Time to Repair Conditions of Acceptability SafetyInstallation Requirements TUV Voltage Max Ripple Current Typical Maximum Power RequirementsData Compression This page intentionally left blank Installation Guide DIP switch & Connector Scsi ID Number Jumper Termination Power SwitchDIP SW Mode Scsi ID3 ID2 ID1 ID0 Power Connector Parity Disable JumperData Compression on Switch Scsi 68 pin Connector Ground BSY +BSY ACK +ACK Ground Diffsens Termpwr Reserved+ATN +RST Ground BSY ACK GroundGround Termpwr Reserved MSG Ground SEL REQ Attaching and Removing the Dust Cover Attaching the Dust Cover Removing the Dust Cover This page intentionally left blank Meaning of each LED indications Tape Motion Cleaning Request Replace TapeSummary of LED Indications LED Inserting Cassettes Operator Action Powering up the SDX-800VHard Reset Hole Removing Cassettes Power-Fail or Scsi Reset Handling Internal Function Normal Status Display Diagnostic and Normal Status DisplaysDiagnostic Status Display Front Panel Test Normal LED indications Tape AlertTape Format Maintenance, Troubleshooting and Service Head Cleaning Troubleshooting Guide Tape is in the drive and will not eject Tape guide surface Cartridge Detail a Photo 2 The Initial Position of the Threading Mechanism Packaging for Return to Sony Clearance for ServiceRead/Write Problems Replace Tape This page intentionally left blank Overview of the Scsi Interface Supported Messages Supported Commands Supported Scsi Commands Command Name Operation Code Scsi Bus Operation Typical Scsi Operation Disconnect Identify Message SpecificationMessage Descriptions Code Direction Parallel Protocol Request 04h Command Complete 00hExtended Message 01h Byte Value Description Synchronous Data Transfer Request 01hSynchronous Data Transfer Request Synchronous Data Transfer Rates Responding Device Sdtr response Implied Agreement Wide Data Transfer Request Byte Value Disconnect 04h Restore Pointers 03hSave Data Pointer 02h Abort 06h Initiator Detected Error 05hMessage Parity Error 09h Message Reject 07h Ignore Wide Residue 23h BUS Device Reset 0ChIdentify 80h-FFh Ignore Wide Residue Message Byte Value Status Specification Scsi Interface This page intentionally left blank Load /UNLOAD Scsi Commands and Page IndexPara Scsi Command OP Code Erase 19h Evpd Inquiry 12hBit Byte Operation Code 12h Obsolete Reserved CmdDT Or Operation Code Reserved Allocation Length Control Sony LSB MSB Bit ByteMSB LSB MSB Vital Product Data Length 0Ah Product Serial number in Ascii Length 32h Reserved 00h Code set 02h Identifier type 01h Identifier length 08h Ieee EUI-64 Code CDB size m-5 CDB usage data Hold LOAD/UNLOAD 1BhImmed Reten Load Load Unload Command Parameter Combinations Hold Reten Load Action LSB Locate 2BhMSB PCR LOG Select 4ChObsolete Reserved Parameter List Length MIC Variable Length Information Parameter Codes Description CodesCode Description Reserved Parameter Pointer LOG Sense 4DhObsolete Reserved PPC Code Control field values Value Type of Parameter Values Log Page Descriptor Supported Log Pages Lbin Log Parameter DescriptorTSD TMC Supported Log Pages12 Threshold Met criteria Threshold Met Criteria Write and Read Error Counters Pages Summary List of Supported Pages Last N Error Events List Length 140h Tape Alert LogBit Byte Reserved Code 2Eh Parameter Code n 5n+1 Tape Alert Log Page Parameter Codes LOG Sense Restart the operation That is not mechanically Length 98h Tape Log Page Sony Unique21 Tape Log Bit Byte Reserved Code 30h TMC Lbin Parameter Length m Parameter Value 23 Tape Capacity Log Bit Byte Code 31h Length 00 20h when AIT bit =0 04 00h when AIT bit =1Tape Capacity Log Page Sony Unique TMC Lbin Parameter Length 04h Drive Usage Log Page Sony Unique Read and Write Frame Error Counter AIT1 Length 58h Data Compression Transfer Log Page Sony Unique32 Data Compression Transfer Log Bit Byte Reserved Code 39h Parameter Code n Length n+1 AIT Log Page Sony Unique33 AIT Log Bit Byte Code 3Ch Reserved TSD TMC Lbin Parameter LOG Sense MIC Fixed Length Information Page Sony Unique 34 MIC Fixed Length Information Bit Byte Code 3Dh Reserved Prth Ponej AITABS MSB Current Amount of Data Written LSB 42-99 24-2729-31 Parameter Code 0017h Element Address Length n-3 MIC Variable Length Information Page Sony UniqueImportant Note Parameter Code Description Mode SELECT6/10 15h and 55h Mode Select 6 CDB Format Bit Byte Operation 37 Sequential-Access Density Codes Code Value 39 Supported Mode Select Page Codes Description Mode Fixed Bit in Read, Write Block Length38 Mode Select Page Header Bit Byte Code Additional Page Length Disconnect-Reconnect Page 02h Dtdc Autoload Mode field Control Mode Page 0AhAutoload Mode Bit Byte Reserved Code 0Ah Length 0Ah DDE RED Data Compression Control Page 0FhDCE CAP Device Configuration Page 10h42 Device Configuration Bit Byte REW Mode Select Medium Partitions Parameter Page 11h IDP Psum Mode Select Informational Exceptions Control Page 1Ch Mrie MSB AIT Device Configuration Page 31h Bit Combination Table Reserved Partition units Append Partition 32h This mode page is not supported47 Append Partition Bit Byte Reserved Code 32h Length Partition Size Descriptor Append Partition example procedure Delete Partition 33h This mode page is not supported Case New tape layout Case 5 with PRTH=0 DBD Mode Sense 6/10 1Ah and 5Ah49 Mode Sense 6 CDB Format PCF Number of Blocks 00 00 00h 52 Supported Mode Sense Page CodesLength 08h MIC Cartridge Mode Sense 31h AIT Device ConfigurationSDX-T3N AIT DEV Ulpbot Prth Ponej ABS MIC MSB Generation LSB Service ActionPersistent Reserve in 5Eh SCOPE-SPECIFIC Address Reservation descriptorReservation Key Scope Type 59 Persistent Reservation Type Codes 58 Persistent Reservation Scope CodesName Description Parameter List Length 18h Service Action Scope TypePersistent Reserve OUT 5Fh Type Service Action SCOPE- Specific Reservation KEY Address Prevent Allow Medium Removal 1Eh Obsolete Reserved Prevent Control Sili Read 08hBit Byte Operation Code 08h Obsolete Reserved Fixed Read Reserved Control Read Attribute 8ChFirst Attribute ID Code Name Description Attribute Values service action64 Read Attribute service action codes Attribute Attribute List service actionAvailable Data n-3 Attribute First Volume Number Number of Volumes Available Partition List service actionVolume List service action Available Data 2h 69 Read Block Limits Data Bit Byte Reserved Read Block Limits 05hObsolete Reserved Control Maximum Block Length Limit 80 00 00h Read Buffer 3Ch Buffer ID The supported values are Description Offset 72 Read Buffer Descriptor Bit Byte ReservedBuffer Capacity MSB Buffer Capacity LSB BOP EOP Read Position 34hTclp Long BPU Block Number 76 Read Position Data Format, long form Bit ByteMPU BPU File Number Supported Page Code 00h Supported Page Code 81h Receive Diagnostic Results 1ChLength 00 02h Length 00 05h Re-Sync Error Code Result a Result B Test Number Release Unit 6/10 17h and 57h Parameter List Length Control MSB MSB Capacity LSB Report Density Support 44hMedia 105 103104 106 171 172 166167 168 179 320 317319 321 Reserved Allocation Length Control Bit Byte Operation Code A3h Reserved Service ActionReport Device Identifier A3h LUN List Length 00 00 08h Report Luns A0h86 LUN reporting parameter list format Bit Byte LUN List Request Sense 03h Obsolete Reserved Allocation Length 1Ch Control CLN EOM ILISksv MEW SKSV0 SKSV1BPV Bytes Description Key Recovered Error90 Sense Key Descriptions Cartridge Fault Append Position ErrorCleaning Failure END-OF-PARTITION / Medium Detected Saving Parameters not Supported MIC Read ErrorParameter Value Invalid Medium Auxiliary Memory Accesible Power ON, RESET, or BUS Device Reset OccurredNot Ready to Ready TRANSITION, Medium MAY have Changed Command Phase Error Aborted CommandInitiator Detected Error Message Received Volume Overflow Reserve Unit 6/10 16h and 56h 91 Reserve Unit 6 CDB format Bit Byte Operation MSB Rewind 01h Obsolete Reserved Immed Control Obsolete Reserved Self Test Send Diagnostic 1Dh94 Diagnostic Page Format Bit Byte Code Reserved UnitOfl 95 Diagnostic Test information SET Device Identifier A4h Reserved Parameter List Length Control Count Space 11hObsolete Reserved Code 98 Space codes ASC/ASCQ EOMSense Key Check Condition 3A 00 Medium not Present Test Unit Ready 00hNot Ready 04 01 Logical Unit is Becoming Ready Write 0Ah Obsolete Reserve Fixed Partition Number Volume NumberWrite Attribute 8Dh MSB Parameter List Length LSB LSB Attribute Write Buffer 3Bh 103 Write Buffer Mode Field Description104 Write Buffer Mode Field Buffer ID Description Offset Write Buffer Number of File-marks or Set-marks Write Filemarks 10hBit Byte Operation Code 10h Obsolete Reserved WSmk Immed Overview Diagnostic TestPower-on Self Test Send Diagnostic command Self Test Send Diagnostic command Individual Test Diagnostic Test Number Summary Send Diagnostic Parameters SCSI-2 Bit Byte Code 81h Reserved Mechanism Controller Kernel Test Receive Diagnostic Result commandSequence Test Main Processor Kernel Test Drive Diagnostics Diagnostics Results Reference Following list of error codes are supported by the drive Error set 2 Diagnostic error This page intentionally left blank Byte Description ASC and Ascq AssignmentsAlphabetic Order Mode Parameters Changed Mechanical Positioning ErrorMessage Error Logical Unit not Supported Appendix B ASC & Ascq Numeric Order Numeric Order Command Sequence Error Appendix C Scsi Commands Op Code Order A3h 10-2 Sony AIT-3Ex drive SDX-800V series Ver.1.1 ASC and Ascq Assignments for AIT drive Sony Unique Byte 11-2 Sony AIT-3Ex drive SDX-800V series Ver.1.1 Appendix E Medium Auxiliary Memory Attribute Read Code 1Bh ReservedHold EOT Reten Load Control With Write MAM Attribute Format Bit Byte MAM Attribute statesAttribute Type MAM attribute identifier range assignments MAM attribute formatsFormat Name Description Attribute Identifiers Attribute Type Standardization Device Common Attributes Attribute Name #Bytes Format Product Serial Number Device VENDOR/SERIAL Number attribute format Bit ByteVendor Identification Medium Usage History attribute format Bit Current Amount of Data Written Appendix E Partition Initialize Count Current Write Reties CountChange Partition Count 11 Medium Common Attributes Attribute Name #Bytes Format Medium Type Information 12 Medium Type and Medium Type Information attributesMedium Type Standard host type attributes 14 Text Localisation Identifier How to initialize a Worm cartridge Write-Protected WP Bit in Mode Sense DataHow to detect a Worm cartridge 31h AIT Device Configuration Bit Byte AIT=0 How to handle the Worm cartridge in the drive END 13-4 Sony AIT-3Ex drive SDX-800 series Ver.1.1 Exiting DR Mode Creating Disaster Recovery TapeConfiguring The Drive For Disaster Recovery Operation Supported Cdrom DR Command Set Inquiry 12h Read TOC Mode Sense/Select Page Code 0x3CReset Handling Appendix H Glossary Appendix H Appendix H 15-4 Sony AIT-3Ex drive SDX-800V series Ver.1.1