Model 465L Ozone Monitor | Teledyne instruction

OPERATION MANUAL

MODEL 465L

OZONE MONITOR

Teledyne Advanced Pollution Instrumentation (TAPI)

9480 Carroll Park Road

San Diego, CA 92121-5201

Phone: 800-324-5190 (toll free in North America) 858-657-9800 (direct)

FAX: 858-657-9816

EMAIL: api-sales@teledyne.com

WEB SITE: http://www.teledyne-api.com/

© 2007-2012 TAPI	05509F DCN6409
Teledyne Advanced Pollution Instrumentation	09 May 2012

Image 1

Teledyne operation manual Model 465L Ozone Monitor

Contents

Model 465L Ozone Monitor Page About Teledyne Advanced Pollution Instrumentation Tapi This page intentionally left blank General Safety Hazard Important Safety Information Mise EN Garde Consignes DE Sécurité Part Name/Description Number About this Manual Revision History Table of Contents Digital Communications Figures Sensor Detail Tables Xii 05509F DCN6409 Preface Introduction This page intentionally left blank Specifications Specifications and Agency Approvals Multi-Stream Specifications SafetyApprovals EMC Phone Other Type Certifications This page intentionally left blank = − InHg × ln ×  273 Principle of Operation 05509F DCN6409 Getting Started Nema AC Power Connection to Monitor Pneumatic Connections Pneumatic Connections, Rack Mount Configuration Sample Gas Connection Pneumatic Connections, Nema Configuration, Multi-Stream Sample System Design in Humid Environments Sample Filtration 05509F DCN6409 Permeation Gas Dryer Option Sample Conditioner Option Rear Panel Electrical I/O Connections Exhaust Connection Electrical I/O Connections Location of I/O Connectors in the Nema ConfigurationAnalog Output Status Outputs Status Name Normal Operating Output # State Status Output Schematic Relay # Function Normal Operating State Hi-Current Relay OutputsRelay # Function Normal Operating State Relay # Function Meaning Multi-Stream Relay Outputs Optional 6.1. RS232 Connection Digital Serial Interfaces6.2. RS485 Connection Ethernet Connection His page intentionally left blank Frequently Asked Questions This page intentionally left blank Options 05509F DCN6409 Front Panel Overview OperationOzone Concentration Display Menu Navigation Keypad Alarm Status LED Color Alarm State Concentration Alarm Status/ResetStream Selector Status/Control Optional Front Panel Menus Status LEDsMenu Navigation Basics Status LED Normal State Editing Numeric Values Front Panel Menu Diagram OFF Analog Step-Test Diag MenuPoint 5V Output MA Output Signal Name Rear Panel Label Function Signal I/O Zero Calibration Memory Reset Span Calibration Span Cal Menu Flow Calibration Optional Electronic Flowmeter only Flow Cal Menu View Menu Config MenuParameter Meaning Units Count SETUP-VARS Menu Property Meaning Default Range Value SETUP-STREAM Menu Multi-Stream Operation Digital Communications Changing Com Port Hardware ConfigurationDigital Communications Overview RS232 Configuration Function DB-9 General I/O Connector Pin SW2 DTE SW2 DCE RS-232 ConfigurationProperty Value Function DB-9 General I/O Connector Pin SW2 DCE RS-485 Configuration Hardware Setup for Configuring the Ethernet Module Ethernet ConfigurationVerifying Network Hardware Connection Link LED Left Side Activity LED Right Side Color Meaning Manually Assigning a Static IP Address Determining a Dynamically Assigned IP Address Dhcp Mode Modbus Register Maps Modbus Commands SupportedDescription Function Code Decimal Address Description Register Type Start Bit # Bits Real-Time Concentration and Status Registers Read Only Instrument Setup and Configuration Registers Read / Write Decimal Address Description Register Type Start Bit # Bits This page intentionally left blank Maintenance Schedule Maintenance and AdjustmentsMaintenance Item Recommended Interval Section Instrument Layout Instrument Layout, Rack Mount Configuration Replacing Internal Particulate Filter Instrument Layout, Nema Configuration UV Lamp Adjustment Sample Pump Replacement UV Lamp Replacement 05509F DCN6409 Sensor Detail Sensor Valve Replacement Configuring the Analog Output Water Drop-Out Filter Option Maintenance Boot Loader Operation Cleaning Exterior Surfaces of the M465L Boot Loader Software Setup Boot Loader Hardware SetupUpload Firmware Verify Firmware This page intentionally left blank Pneumatic Diagram TroubleshootingReference Drawings RACK-MOUNT Version only Interconnect Diagram Status LED/Output Definitions Sensor OK Pneumatic ErrorInvalid Reading Check Lamp Pressure Too Low Pressure Too High This page intentionally left blank Factory Calibration CalibrationZero Calibration This page intentionally left blank Spare Parts 12.1. M465L Rack Mount Spare Parts List Part Number Description 12.2. M465L Nema Spare Parts List CONNECTOR, 16 PIN, W/SCREW Flange This page intentionally left blank Permeation Gas Dryer Index