Teledyne 465L - page 14

Teledyne API Model 465L O3 Monitor Operation Manual

xii 05509F DCN6409

This page intentionally left blank.

Contents

Main OPERATION MANUAL MODEL 465L OZONE MONITOR Page ABOUT TELEDYNE ADVANCED POLLUTION INSTRUMENTATION (TAPI) Notice of Copyright Trademarks Page IMPORTANT SAFETY INFORMATION CONSIGNES DE SCURIT ABOUT THIS MANUAL REVISION HISTORY TABLE OF CONTENTS Page FIGURES Page TABLES Page 1. INTRODUCTION 1.1. Preface Page 2. SPECIFICATIONS AND AGENCY APPROVALS 2.1. Specifications 2.2. Approvals 2.2.1. Safety 2.2.2. EMC 2.2.3. Other Type Certifications Page 3. PRINCIPLE OF OPERATION C Page 4. GETTING STARTED Page Page 4.1.1. Sample Gas Connection 4.1.1.1. Sample Filtration 4.1.1.2. Sample System Design in Humid Environments Page Page 4.1.2. Exhaust Connection 4.2. 4.2.1. Location of I/O Connectors in the NEMA Configuration 4.2.2. Analog Output 4.2.3. Status Outputs Page 4.2.4. Hi-Current Relay Outputs 4.2.5. Multi-Stream Relay Outputs (Optional) 4.2.6. Digital Serial Interfaces 4.2.6.1. RS232 Connection 4.2.6.2. RS485 Connection 4.2.6.3. Ethernet Connection Page 5. FREQUENTLY ASKED QUESTIONS Page 6. OPTIONS Page 7. OPERATION 7.1. 7.1.1. Ozone Concentration Display 7.1.2. Menu Navigation Keypad 7.1.3. Stream Selector Status/Control (Optional) 7.1.4. Concentration Alarm Status/Reset 7.1.5. Status LEDs 7.2. 7.2.1. Menu Navigation Basics 7.2.2. Editing Numeric Values Teledyne API Model 465L O3 Monitor Operation Manual Figure 7-2: Front Panel Menu Diagram (Page 1) 05509F DCN6409 43 Teledyne API Model 465L O3 Monitor Operation Manual Figure 7-3: Front Panel Menu Diagram (Page 2) 44 05509F DCN6409 7.2.3. DIAG Menu 7.2.3.1. Analog Step-Test 7.2.3.2. Signal I/O 7.2.3.3. Memory Reset 7.2.3.4. Zero Calibration 7.2.3.5. Span Calibration 7.2.3.6. Flow Calibration (Optional Electronic Flowmeter only) Page 7.2.4. VIEW Menu 7.2.5. CONFIG Menu 7.2.6. SETUP-VARS Menu the serial number tag on the rear of the instrument. N/A 1 9999 7.2.7. SETUP-STREAM Menu 7.3. 8. DIGITAL COMMUNICATIONS 8.1. 8.2. Page 8.3. 8.4. 8.5. 8.5.1. Hardware Setup for Configuring the Ethernet Module 8.5.2. Verifying Network Hardware Connection 8.5.3. Determining a Dynamically Assigned IP Address (DHCP Mode) 8.5.4. Manually Assigning a Static IP Address 8.6. 8.6.1. MODBUS Commands Supported 8.6.2. Notes on MODBUS registers 8.6.3. Real-Time Concentration and Status Registers (Read Only) 8.6.4. Instrument Setup and Configuration Registers (Read / Write) Page Page 9. MAINTENANCE AND ADJUSTMENTS 9.1. 9.2. 9.3. 9.4. 9.5. 9.6. Page 9.7. 9.8. Maintenance 9.9. Q1 9.10. 9.11. 9.11.1. Boot Loader Hardware Setup 9.11.2. Boot Loader Software Setup 9.11.2.1. Upload Firmware 9.11.2.2. Verify Firmware Page 10. TROUBLESHOOTING 10.1. 10.1.1. Pneumatic Diagram Teledyne API Model 465L O3 Monitor Operation Manual 10.1.2. Interconnect Diagram RACK-MOUNT VERSION ONLY 10.2. LEDs or Status Outputs 10.2.1. Sensor OK 10.2.2. Invalid Reading 10.2.3. Check Lamp 10.2.4. Pneumatic Error 10.2.4.1. Pressure Too High 10.2.4.2. Pressure Too Low Page 11. CALIBRATION 11.1. 11.2. Page 12. SPARE PARTS 12.1. 12.2. Page Page INDEX