Texas Instruments TMS320C6202 specifications Recommended operating conditions, MIN NOM MAX Unit

TMS320C6202

FIXED-POINT DIGITAL SIGNAL PROCESSOR

SPRS072B ± AUGUST 1998 ± REVISED AUGUST 1999

absolute maximum ratings over operating case temperature range (unless otherwise noted)²

Supply voltage range, CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.3 V to 2.3 V Supply voltage range, DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.3 V to 4 V Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.3 V to 4 V

Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.3 V to 4 V

Operating case temperature range, TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0_C to 90_C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±55_C to 150_C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to VSS.

recommended operating conditions

INFORMATION

CVDD	Supply voltage
DVDD	Supply voltage
VSS	Supply ground
VIH	High-level input voltage
VIL	Low-level input voltage
IOH	High-level output current
IOL	Low-level output current
TC	Operating case temperature

MIN	NOM	MAX	UNIT
1.71	1.8	1.89	V
3.14	3.30	3.46	V
0	0	0	V
2.0			V
		0.8	V
		±8	mA
		8	mA
0		90	_C

ADVANCE

electrical characteristics over recommended ranges of supply voltage and operating case temperature (unless otherwise noted)

	PARAMETER					TEST CONDITIONS		MIN	TYP	MAX	UNIT
VOH	High-level output voltage	DVDD = MIN,					IOH = MAX	2.4			V
VOL	Low-level output voltage	DVDD = MIN,					IOL = MAX	0.6			V
I	Input current³	V = V		SS		to DV	DD	±10			uA
I		I
IOZ	Off-state output current	VO = DVDD or 0 V						±10			uA
I	Supply current, CPU + CPU memory access§	CV	DD		= NOM,		CPU clock = 200 MHz		TBD		mA
DD2V
I	Supply current, peripherals¶	CV	DD		= NOM,		CPU clock = 200 MHz		TBD		mA
DD2V
IDD3V	Supply current, I/O pins#	DVDD = NOM,					CPU clock = 200 MHz		TBD		mA
Ci	Input capacitance							10			pF
Co	Output capacitance							10			pF

³TMS and TDI are not included due to internal pullups. TRST is not included due to internal pulldown. § Measured with average CPU activity:

50% of time:	8 instructions per cycle, 32-bit DMEM access per cycle
50% of time:	2 instructions per cycle, 16-bit DMEM access per cycle

¶Measured with average peripheral activity:

50% of time:	Timers at max rate
	McBSPs at E1 rate
	DMA burst transfer between DMEM and SDRAM
50% of time:	Timers at max rate
	McBSPs at E1 rate
	DMA servicing McBSPs
# Measured with average I/O activity (30-pF load, SDCLK on):
25% of time:	Reads from external SDRAM
25% of time:	Writes to external SDRAM
50% of time:	No activity

28 POST OFFICE BOX 1443 •HOUSTON, TEXAS 77251±1443