THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V | Toshiba B-SX4T

2.PRINTER SETUP

ENGLISH VERSION EO1-33058

2.13 Threshold Setting

2.13Threshold Setting (Cont.)

(3) Press the [PAUSE] key until the target sensor type is displayed.

	<3>ADJUST SET			Black Mark Sensor
	THRESHOLD<R>1.0V			Black Mark Sensor
	THRESHOLD<R>1.0V

		[PAUSE]
	<3> ADJUST SET			Feed Gap Sensor
	THRESHOLD<T>1.4V

NOTE:

Pressing the [FEED] key one time causes a –0.1V change, up to 0.0V.

Pressing the [RESTART] key one time causes a +0.1V change, up to +4.0V.

(4)Set a threshold voltage (calculated in Sensor Adjustment Menu) by using the [FEED] or [RESTART] key, as shown below.

Threshold voltage = Midpoint between voltage at a print area and voltage at a gap/black mark

Black Mark Sensor		Feed Gap Sensor
THRESHOLD<R>4.0V		THRESHOLD<T>4.0V
THRESHOLD<R>3.9V	[RESTART]	THRESHOLD<T>3.9V
THRESHOLD<R>3.8V		THRESHOLD<T>3.8V
THRESHOLD<R>0.1V	[FEED]	THRESHOLD<T>0.1V
THRESHOLD<R>0.0V		THRESHOLD<T>0.0V

(5)After choosing a threshold voltage, press the [PAUSE] key.

(6)To check for a proper operation, issue the pre-printed media in online. If an error still occurs even after a manual threshold setting, change the threshold voltage a little, and retry.

E2-68

Image 82

Toshiba B-SX4T owner manual THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V

Contents

SX4T Series CE Compliance for EU only Vorsicht SX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents EA3-1 EA1-1EA2-1 EA4-1 Introduction Features Unpacking Product Overview Doc. No. EO2-33021 AccessoriesNo FM1647000 Quality Control Report 1 sheet Rear View DimensionsFront View Following chapters Operation Panel Interior Options Option Name Type Description Procedure Printer SetupSetup Flow Reference Installation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionRemove the Locking Screw that secures the Media Sensor Strip mode Option Batch modeSTANDARD/PEEL OFF position Built-in rewinder mode Option Cut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the Printer Pcmcia Cards Paragraphs outline how to insert Pcmcia cardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Sequentially After selecting a character code, press the Pause key Character Code SelectionUse the Feed or Restart key to select a desired option Character Zero Selection Data Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause key Parity Selection Stop Bit SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause key Head Up Cut/Rewinder Selection Feed key After selecting the solenoid type, press the Pause key Solenoid Type SelectionRibbon Saving Function Selection Control Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause key Euro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause key Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key Input Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type Selection Plug & Play Selection Centronics Interface SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Label End/Ribbon End SelectionAfter selecting the Pre-strip function, press the Pause key Reverse Feed Speed Selection Maxi Code Specification SelectionAfter selecting the Back Feed Speed, press the Pause key Print Head Type Selection System Mode Password SettingAfter selecting a print head type, press the Pause key Use the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause key Receive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel Interface Windows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/ME Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print Test When using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine Adjustment Position and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Select the sensor to be adjusted by using the Feed key Threshold SettingJam errors Manually set Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation Panel Operation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart key Media is slack Take up any slack in the media Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Ribbon has run out Load a new ribbon. Then press Possible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Refer to .1 Media Cutter blade is dirty Clean the cutter blade⇒Section Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel SX4T-GS20-QM-R Media Type Supply SpecificationsMedia Label Label Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and label Symbols in the message Appendix 1 Messages and Leds Base LAN Board is being Printer is waiting for a password to Be enteredWrong password was entered Initialized Printer did not succeed in writing Following message appears Appendix 2 Interface Parallel interface Centronics Standard Connector PIN Serial interface Standard 100BASE-TX UTP category Physical LayerLAN cable Cable length Segment length Max m Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU SX704-RFID-U2-US-R When purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digits Customer bar code UPC-A+5 digitsIndustrial 2 KIX Code Appendix 5 Glossaries Media and ribbon See Black mark sensorDevice used to remove labels from the backing paper See Feed gap sensor Index 3-1, A1-1 Index Waste Recycling information for users EO1-33058E