Manuals / Toshiba / Computer Equipment / Printer

Toshiba CB-426-T3-QQ, EO1-33027E owner manual Loading the Media

Models: EO1-33027E CB-426-T3-QQ CB-426-T3

1 122

Download 122 pages 20.93 Kb

Page 19

Chapter 2 Printer Installation

2.5Loading the Media

Labels or tags can be loaded in the printer. The media loading procedure depends on which media is going to be used.

1Open the Top Cover.

Top Cover

Note:

The Supply Shaft cannot be kept level because of its weight, as the printer becomes older. So before loading the media, adjust the Supply Shaft so that it can be kept level.

2Lift the Pinch Roller Lever to the ROLLER RELEASE position to open the Pinch Roller Unit.

Pinch Roller Unit

Pinch Roller Lever

(To ROLLER RELEASE)

3Loosen the screw on the Supply Shaft Holder Stand.

4Fit the Supply Shaft Holder Stand to the Supply Shaft, as illustrated below. The Supply Shaft Holder Stand moves up or down so that the Supply Shaft is kept level.

Supply Shaft

Screw

Supply Shaft Holder Stand

5Remove the Supply Shaft Holder Stand from the Supply Shaft, when adjustment to its height is complete.

11

Image 19

Toshiba CB-426-T3-QQ, EO1-33027E owner manual Loading the Media

Contents

CB-426-T3-QQ For Canada onl y Safety Summary Safety PrecautionsMeanings of Symbols Any other than the specified AC voltage is prohibited Iii Request Regarding Maintenance Table Contents of Contents TOC Product Overview Introduction Features UnpackingAccessories Accessories and OptionsEnhancement Kit Cool ReleaseOptions Rear View DimensionsAppearance Front ViewInterior Operation PanelMedia Slide Printer InstallationInstalling the Accessories Fan FiltersConnecting the Printer to Your Computer Connecting the Power Cord Turning on the Printer Turning on/off the PrinterPrinter Turning offLoading the Media Measure width of the media that will be loaded Slide the Supply Roll Holder inside to the loaded media RightWrong Side View of the Printer Top View of the PrinterInformation AdditionalBlack Mark Sensor Sensor AdjustmentsFeed Gap Sensor Media Sensor AdjustmentMedia Sensor Adjustor Black Mark Sensor Sensitivity AdjustmentOpen the Top Cover Ribbon Width Media Width Loading ProcedureLoading the Ribbons For Hot Release Ribbon PositionsLoading ProcedureRibbon Module Print Head Block Part Name Quantity Loading the RibbonsInstalling the Ribbon Plate Ribbon Guides Installing the SPThem in the direction of the arrow Installing the Ribbon Tension Sheet Loading the Cold Release Ribbons Preparation Installation Procedure For Windows98Printing System RequirementsClick Next InstallationChapter Installation Procedure Adding the Printer For Windows98 Click Have Disk Chapter Printing Uninstalling the Printer Driver Chapter Displaying Printer PropertiesProperties This is a summary of the main properties for CB-426-T3 Summary of PropertiesSelecting a label size SetupUser Defined cannot be renamed Creating a new label size∙ a preview will be shown, as each option is selected OrientationMiscellaneous User CommandsName Tab Settings See SectionTransfer Mode Print Density Adjustment Printing PreferencesClick Export. The Save Devices Settings File screen appears Click Import. The Open Device Settings File screen appears To enable the saved settings, use the following proceduresCont Dithering GraphicsColor Color Setup Do not mark the Color 2 checkbox when Head 1 is not used Click the color swatch to change the Hue and saturation Sat Click Color Registration on the Graphics property Color RegistrationY5 in Vertical Y on Align Color Yellow/Black Color 0 Yellow SampleBar Fonts Specifying a New Font Style Font Style Label Gap StockPrint Method SensorIssue Settings Fine Adjustment Print Density Adjustment Transfer ModeOptions Check Print Head TestingTesting Print Test LabelCut MaintenanceReset FeedPrint Test ProceduresOn the File menu, click Print Printing a LabelPrinting a Label Illuminates when Flashes when Online ModeOperation Panel No Paper ResetOperation On LineCleaning MaintenancePrint Head/Platen Pinch Roller/Feed Roller/Media Guide Turn off the printer. Unplug the power cordRibbon Modules Covers and PanelsError Messages TroubleshootingError Messages Problems/Causes Solutions Switch to the right Back Tension Possible Problems Causes Solutions Possible ProblemsFrom the Print Head Block From the Pinch Roller UnitWhen the Ribbon is Torn Apart A1.1 Printer Appendix 1 SpecificationsModel CB-426-T3-QQ Label Tag A1.2 Options A1.3 MediaName Model Description A1.3.1 Media TypeBelow A1.3.2 Detection Area of the Transmissive SensorReflective Sensor A1.3.3 Detection AreaA1.3.4 Effective Print Area Type Spool Type A1.4 RibbonAppendix 2 DIP Switches Function A2.1 DIP Switch aOFF Even A2.2 DIP Switch BA2.3 Ribbon Near End Detection Actions Path to Find the Property See Section Label SettingsIssue Mode Settings Appendix 3 Quick Reference for PrintingActions Path to the Property See Section Other SettingsFunction See Section Remarks TABLCD Messages Printer Status Symbols in the MessageAppendix 4 Message and LED LED Indication` YES Message and LEDA5.1 Operation Panel Appendix 5 System ModeA5.2 Overview 3TEST Print 2PARAMETER SET4RAM Clear Sensor None A5.3 Self-Diagnostic TestAuto Diagnostic MaintenanceChecking A5.4 Parameter SettingHead Error Head CheckPosition A5.4 Parameter Making Positional AdjustmentsPrint Density Adjusting Print Density Head 1 and HeadPrint Speed 6/S Head AdjustIssue Count Print ConditionPrinting the X/Y Direction Alignment Caliper-shaped Pattern AdjustHEAD1 B00 DirectionHEAD1 F00 HEAD2 F00Font Code PC-850 HEAD2 B00Check Printer ParaEuro Code PM AdjustCode Auto Pulse Motor AutoRibbon Head SelectHEAD1 on HEAD2 onSpecifying the Print Condition for the Test Print A5.5 Test PrintPause key again Printing out the Slant Line Pattern Types no CUTQuality High Paper FeedBarcode Slant LINE2Color CharactersComplete A5.6 RAM ClearNo RAM Clear Mainte CNT ClearPrint Step Clear Clearing the Print DistanceALL Color Memory Check A5.7.1 Self-Diagnostic Test Result Sample and DescriptionsSwitch Check A5.7 Additional InformationParameters Maintenance CounterA5.7.6 Magnified Views of Slant Line Pattern A5.7.5 X-Coordinate Fine AdjustmentA5.7.3 Cut Operation Example A5.7.4 Pulse Motor SpeedInitial Value 110 111 Appendix 6 Interface