Section 3 - Service and Repair

9/16" Wrench

1/4" Copper Water

Supply Line

7/16" Wrench

From Water Supply

to Ice Maker

ULIN_S_0168_A

Figure 70

3.Your U-Line icemaker requires a drain connection. This unit can be purchased with or without a factory-installed drain pump. If a pump is not installed in the appliance you must use the gravity drain style installation OR install a pump per the installation instructions found on www.U-Line.com.

4.Slide two hose clamps onto the drain connection on the rear of the appliance. Insert the barbed fitting half-way into this connection. On the other end of the barbed fitting attach the 5/8" braided tubing. Slide a clamp onto each side of the barbed fitting as shown (Figure 71 & 70).

ULIN_S_0166b1_A

Figure 71

Drain Fitting from

Back of Unit

5/8" x 5/8" Barb Connector

Worm Clamps

Drain Line

ULIN_S_0166b2_A

Figure 72

5.Determine the location of your drain and begin to route the drain tubing in that direction. If using the gravity drain option you must provide 1/4" drop every foot of line. For drain pump application you must not go higher than 10 feet of lift. The lift should be made vertically at the beginning of the drain line. After the lift try and provide 1/4" drop every foot of line to the drain location.

6.Connect the water supply fitting by screwing the brass garden hose fitting to the water valve in the rear of the unit. Tighten this fitting with a pliers. Do not use Teflon tape or joint compound on the fitting. The rubber washer provides an adequate seal. Other materials could cause blockage of the valve. The copper water line should now be clamped to the rear of the unit to prevent rotation when sliding in. Remove the clamp from the unit, slide the tube into it and reattach using the 1/4" nut driver as shown (Figure 71 and 70).

7.Plug in the unit and put the unit into OFF mode by holding the power key for 10 seconds. Not doing this will cause the unit to fill with water for three minutes.

8.Turn on the water supply and ensure the connections are free of leaks.

9.Begin to push the appliance into the desired cabinet opening. The copper tubing should remain in two coils behind the unit. While pushing the unit into the opening continuously reroute the drain tube to avoid kinks. The most common installation pulls the slack into an adjacent cabinet or basement area. Again, if installing a gravity drain, ensure you provide proper slope

3-62

Page 77
Image 77
U-Line 2275DWRWOL, 2275DWRWS, 2175WCOL, CLRCO2175, CO2175F, CO2175/CO2275DWR, CLR2160, 2175RF, 2175BEV, 2115WCOL, 2115R ULINS0168A

2175R, 2115R, 2115WC, 2175/2275DWRR, 2115WCOL specifications

The U-Line CLRCO2175 and CLR2160 are standout models in the world of compact refrigeration solutions, offering remarkable features tailored for modern living. Known for their slim design and efficient performance, these models are perfect for homeowners seeking added convenience without sacrificing space or style.

The U-Line CLRCO2175 boasts a capacity of 5.3 cubic feet, providing ample storage while maintaining a sleek profile. Its glass door is a key highlight, featuring Low-E argon gas-filled glass which not only enhances visibility but also provides energy efficiency by minimizing heat transfer. The model includes a built-in ice maker, delivering a continuous supply of fresh ice, which is ideal for entertaining or everyday use.

On the other hand, the CLR2160 offers a slightly smaller capacity of 3.4 cubic feet, perfectly suited for tighter spaces while still delivering on performance. It features the same stylish glass door and energy-efficient insulation, ensuring that your favorite beverages and snacks are kept at optimal temperatures.

Both models are equipped with a digital control panel that allows for precise temperature adjustments, catering to the specific needs of various items from wine to soft drinks. The internal shelving is adjustable, making it easy to customize the interior configuration to accommodate different bottle shapes and sizes.

Energy efficiency is a driving consideration in these models, as they are designed to consume less power compared to traditional refrigerators. This not only helps in reducing utility bills but also minimizes the environmental impact. Furthermore, U-Line has implemented noise-reducing technologies, ensuring quiet operation—ideal for placement in living spaces or open floor plans.

The sleek aesthetic of the CLRCO2175 and CLR2160 can seamlessly blend into various decor styles, from contemporary to traditional. With their stainless-steel finishes and elegant edge-to-edge glass doors, they serve not just as appliances but also as stylish additions to home interiors.

In conclusion, the U-Line CLRCO2175 and CLR2160 offer exceptional features and technologies tailored for modern living. Their space-saving designs, energy-efficient performance, and stylish aesthetics make these models essential choices for those looking to enhance their home with versatile refrigeration solutions. Whether entertaining guests or enjoying a quiet evening at home, these appliances provide the reliability and functionality needed in today’s fast-paced lifestyle.