Vidikron Vision 75, Vision 65 specification

Installation

Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, these brackets bring the mounting points for the projector mounting plate (included with the projector ceiling mount kit) from the bottom of the projector up and around the AutoScope lens motor housing. For floor installations (where the projector is upright), the adapters allow the projector to lie flat on the mounting surface.

Using the four (4), supplied M6 x 12mm Flat-Head Phillips screws (item #6), attach the AutoScope Ceiling Mount Adapters/Projector Stands (items #4 and #5) to the projector as shown in Figure 3-6.

Figure 3-6. Vision 65/75 with Ceiling Mount Adapters/Projector Stands

DO NOT OVER-TIGHTEN THE SCREWS.

Caution

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

21

Image 37

Vidikron Vision 75 operation manual Vision 65/75 with Ceiling Mount Adapters/Projector Stands

Contents

65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and Troubleshooting Serial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram About This Manual 1IntroductionThis Manual If you need Turn to Using This Manual Description, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a Glance Temp LED POWER/STANDBY LED Indicates power status as follows Vision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectors Vision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectors Volt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 65/75 Remote ControlComp 2 / RGB Source Selection Buttons On / OFFVID S-Video Cursor Keys Memory Preset Buttons Picture Adjustment Buttons BRT BrightnessContrast COL Color Lens Picture-In-Picture PIP Controls Remote Control 3InstallationOperation Installation Overview Quick SetupStep Procedure For Details, Refer to If installing a CineWide-equipped projector Install Projector Installation Options Installation ConsiderationsInstallation Type Advantages Considerations Throw Range Throw Ratio Throw Ratios for the Vision 65/75 SeriesProjector Model Floor Installation Ceiling InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens Mount Motor AutoScope motor assembly Vision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens Motor Do not OVER-TIGHTEN the Screws Base Plate Prismatic Lens Vision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75 Using the On-Screen Menus on Adjusting the ProjectorHeight or Projection Angle Connections to the Vision 65/75 Connecting Source65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection Connection AutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other Equipment Power source Turning on the Power Primary Lens Adjustments Changing the OSD Language Adjusting the Picture OrientationZoom Zo om Out Focus Installing and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage Plate Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Whitney Prismatic Adjustment Adjusting the Lens Height Y Anamorphic Lens Top View 4Operation Selecting an Aspect Ratio Adjusting the PictureSelecting Video Memory Selecting An Input Source Using the On-Screen Menus Using Picture-In-Picture PIP Picture Adjust SetupInstallation Source Select Perform the adjustments in the order listed here Picture AdjustSource Select Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menu Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Aspect Ratio SettingsDescription Cinema Fit a 2.351 screen Installation Vertical Keystone Correction Horizontal Keystone Correction Pincushion Correction Operation Information Setup Refer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on again Settings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial Communications Serial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7Specifications Home Theater Calibration Specifications Vision Specifications Vision Model 75 SeriesIndustry-Standard Specifications Vision Model 65 Series Industry-Standard Specifications Vision Model 75 Series Dimensions Power RequirementsWeight without lens Limited Warranty Vision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 Dimensions Format Resolution Supported Signal Timings Supported TimingsMHz Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal Timings Sdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March