AutoScope Lens Motor Rear | Vidikron Vision 75, Vision 65 specification

Installation

If you are installing a Vision 65/75/CineWide with AutoScope, use the cable supplied with the AutoScope Lens Motor to connect the motor to the 12-volt trigger output as shown in Figure 3-15.

Connecting 12-Volt Trigger Output to External Theater Equipment

S-VID /

VID-S

3.5-mm mini plug

AutoScope

Lens Motor (Rear)

Power	AC Input
Switch

Figure 3-15. Connecting the 12-Volt Trigger Output to the AutoScope Lens Motor

If your home theater contains a retractable screen, screen mask or other 12-volt trigger-activated equipment, connect it to the 12-volt trigger output as shown in Figure 3-16.

S-VID /

VID-S

3.5-mm mini plug

to other,
12-volt				Black = Ground (Sleeve)
trigger-activated equipment
				Red = +12V (Tip)
(screen, screen mask etc.)

Figure 3-16. Connecting the 12-Volt Trigger Output to Other Equipment

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

31

Image 47

Vidikron Vision 75, Vision 65 AutoScope Lens Motor Rear, Connecting the 12-Volt Trigger Output to Other Equipment

Contents

65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and Troubleshooting Serial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram This Manual 1IntroductionAbout This Manual If you need Turn to Using This Manual Description, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a Glance Temp LED POWER/STANDBY LED Indicates power status as follows Vision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectors Vision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectors Comp 2 / RGB Vision 65/75 Remote ControlVolt 250 mA Trigger Output 3.5-mm, mini phono jack Cursor Keys On / OFFSource Selection Buttons VID S-Video COL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons Contrast Lens Picture-In-Picture PIP Controls Operation 3InstallationRemote Control If installing a CineWide-equipped projector Install Quick SetupInstallation Overview Step Procedure For Details, Refer to Advantages Considerations Installation ConsiderationsProjector Installation Options Installation Type Projector Model Throw Ratios for the Vision 65/75 SeriesThrow Range Throw Ratio Vertical and Horizontal Position Ceiling InstallationFloor Installation Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens Mount Motor AutoScope motor assembly Vision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens Motor Do not OVER-TIGHTEN the Screws Base Plate Prismatic Lens Vision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75 Height or Projection Angle Adjusting the ProjectorUsing the On-Screen Menus on 65/75 Connecting SourceConnections to the Vision 65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection Connection AutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other Equipment Power source Turning on the Power Zo om Out Focus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments Zoom Installing and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage Plate Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Whitney Prismatic Adjustment Adjusting the Lens Height Y Anamorphic Lens Top View Selecting An Input Source Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting Video Memory Using the On-Screen Menus Using Picture-In-Picture PIP Source Select SetupPicture Adjust Installation Source Select Picture AdjustPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menu Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Description Aspect Ratio SettingsAspect Ratio Cinema Fit a 2.351 screen Installation Vertical Keystone Correction Horizontal Keystone Correction Pincushion Correction Operation Information Setup Refer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on again Settings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial Commands Serial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7Specifications Industry-Standard Specifications Vision Model 75 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 65 Series Limited Warranty Power RequirementsDimensions Weight without lens Vision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 Dimensions MHz Supported Signal Timings Supported TimingsFormat Resolution Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal Timings Sdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March