Vision 65/75 Rear Panel | Vidikron Vision 75 guide

Controls and Functions

2.2

Vision 65/75 Rear Panel

Figure 2-3shows the Vision 65/75 rear panel.

1

2

3

4

5

6

7

S-VID /

VID-S

10

9

8

Figure 2-3. Vision 65/75 Rear Panel

1.HDMI 1 (Digital)

HDCP-compliant digital video input for connecting a DVD player or HD tuner with a DVI or HDMI output.

2.HDMI 2 (Digital)

3.COMP 1 (RCA connectors)

Standard- or high-definition (480i/480p/576i/576p/720p/1080i/1080p) Component (YPrPb) input for connecting a DVD/HD-DVD/BD player, HD set-top box or other SD/HD source.

4.COMPOSITE VIDEO INPUT

Standard composite video input for connecting a VCR, laser disc player or other composite video source.

5.S-VIDEO

A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.

6.POWER INPUT (100 to 240 VAC) Connect the Vision 65/75 to power here.

7.MAIN POWER SWITCH

Disconnects or applies power to the Vision 65/75.

8. RS-232 CONTROL PORT

A female, RJ-11 connector for interfacing with a PC or home theater automation/control system.

8	Vidikron Vision Model 65/Model 75 Installation/Operation Manual

Image 24

Vidikron Vision 75 operation manual Vision 65/75 Rear Panel, Hdmi 2 Digital Comp 1 RCA connectors

Contents

65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Maintenance and Troubleshooting Operation Serial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram 1Introduction About This ManualThis Manual Using This Manual If you need Turn to Description, Features and Benefits Optional Accessories Vision 65/75 at a Glance Vision 65/75 Front/Side/Top View POWER/STANDBY LED Indicates power status as follows Temp LED Cable Access Door Open to access connectors Vision 65/75 Rear/Bottom/Side View Hdmi 2 Digital Comp 1 RCA connectors Vision 65/75 Rear Panel Vision 65/75 Remote Control Volt 250 mA Trigger Output 3.5-mm, mini phono jackComp 2 / RGB On / OFF Source Selection ButtonsVID S-Video Cursor Keys Picture Adjustment Buttons BRT Brightness Memory Preset ButtonsContrast COL Color Picture-In-Picture PIP Controls Lens 3Installation Remote ControlOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a CineWide-equipped projector Install Installation Considerations Projector Installation OptionsInstallation Type Advantages Considerations Throw Ratios for the Vision 65/75 Series Throw Range Throw RatioProjector Model Ceiling Installation Floor InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Installing the Optional CineWide Lens Mount Fixed CineWide Base Plate Cylindrical Lens AutoScope motor assembly Motor Vision 65/75 with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor Installation Base Plate Prismatic Lens Do not OVER-TIGHTEN the Screws Vision 65/CineWide or Vision 75/CineWide Mounting the Vision 65/75 Floor Mounting Upright Adjusting the Projector Using the On-Screen Menus onHeight or Projection Angle Connecting Source Connections to the Vision 65/7565/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections Connection 14. RS-232 Control System Connection 16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor Rear Turning on the Power Power source Changing the OSD Language Adjusting the Picture Orientation Primary Lens AdjustmentsZoom Zo om Out Focus Installing and Adjusting the CineWide Anamorphic Lens These instructions Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Adjusting the Geometry Anamorphic Lens Top View Adjustment Whitney Prismatic Adjusting the Lens Height Y Anamorphic Lens Top View Selecting an Aspect Ratio Adjusting the Picture 4OperationSelecting Video Memory Selecting An Input Source Using Picture-In-Picture PIP Using the On-Screen Menus Setup Picture AdjustInstallation Source Select Picture Adjust Perform the adjustments in the order listed hereSource Select You must enter a passcode to access the ISF menu Typical Pluge Pattern for Adjusting Brightness Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Settings Aspect RatioDescription Cinema Installation Fit a 2.351 screen Horizontal Keystone Correction Vertical Keystone Correction Pincushion Correction Operation Setup Information Refer to the instructions for your computer Is powered off, then on again This menu should be used by ISF-certified technicians only Settings reduce the image brightness CIE 1931 Chromaticity Diagram Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial Communications Serial Communications Serial Commands Serial Communications 7Specifications Vision 65/75 Specifications Specifications Vision Model 75 Series Home Theater Calibration Specifications VisionIndustry-Standard Specifications Vision Model 65 Series Industry-Standard Specifications Vision Model 75 Series Power Requirements DimensionsWeight without lens Limited Warranty Vision 65/75 Dimensions Vision 65/75 Dimensions with Optional Fixed Anamorphic Lens Supported Signal Timings Supported Timings Format ResolutionMHz Supported Signal Timings Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Sdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March