Yamaha CLP-F01 owner manual General Midi Mode On, Data format F0H 7EH XnH 09H 01H F7H

(2) Universal Non-Realtime Message (GM On)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

	[F7H]
F0H =	Exclusive status
7EH =	Universal Non-Realtime
7FH =	ID of target device
09H =	Sub-ID #1=General MIDI Message
01H =	Sub-ID #2=General MIDI On
F7H =	End of Exclusive
or
F0H =	Exclusive status
7EH = Universal Non-Realtime
XnH =	When received, n=0~F.
	X = don’t care
09H =	Sub-ID #1=General MIDI Message
01H =	Sub-ID #2=General MIDI On
F7H =	End of Exclusive

When the General MIDI mode ON message is received, the MIDI system will be reset to its default settings.

This message requires approximately 50ms to execute, so suffi-cient time should be allowed before the next message is sent.

8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] -> [mmH] -> [llH] -> [ddH] -> [F7H]

F0H = Exclusive status 43H = YAMAHA ID

1nH = When received, n=0~F. When transmitted, n=0.

4CH = Model ID of XG hhH = Address High mmH = Address Mid llH = Address Low ddH = Data

F7H = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI sys- tem will be reset to its default settings.

The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

	[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->
	[ccH] -> [F7H]
F0H =	Exclusive status
43H =	YAMAHA ID
0nH =	When received, n=0~F.
	When transmitted, n=0.
4CH = Model ID of XG
aaH =	ByteCount
bbH =	ByteCount
hhH =	Address High
mmH = Address Mid
llH =	Address Low
ddH =	Data
ccH =	Check sum
F7H =	End of Exclusive

•Receipt of the XG SYSTEM ON message causes reinitializa- tion of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before sending the CLP-F01 another message.

•XG Native Parameter Change message may contain two or four bytes of parameter data (depending on the parameter size).

•For information about the Address and Byte Count values, refer to Table 1 below. Note that the table’s Total Size value gives the size of a bulk block. Only the top address of the block (00H, 00H, 00H) is valid as a bulk data address.

9.SYSTEM EXCLUSIVE MESSAGES (Clavinova MIDI Format)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] -> [F7H]

F0H = Exclusive status 43H = Yamaha ID

73H = Clavinova ID

01H =	Product ID (CLP common)
or
7FH=	Extended Product ID
47H =	Product ID
nnH =	Substatus
nn	Control
02H	Internal MIDI clock
03H	External MIDI clock
06H Bulk Data (the bulk data follows 06H)
F7H =	End of Exclusive

*When nn=02H or 03H, CLP common ID (01H) is recog- nized as well as 7FH, 47H.

BULK DUMP FORMAT
F0H, 43H, 73H
7FH, 47H	= Product ID
06H	= Bulk ID
05H	= Sequence data
0nH, 0nH, 0nH, 0nH	= Data length
[BULK DATA]	=
[CHECK SUM (1byte)]	= 0-sum (BULK DATA)
F7H	= End of Exclusive

10.SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [7FH] ->[47H] ->

	[11H] -> [0nH] -> [ccH] -> [vvH] -> [F7H]
F0H =	Exclusive status
43H =	Yamaha ID
73H =	Clavinova ID
7FH =	Extended Product ID
47H =	Product ID
11H =	Special control
0nH = Control MIDI change (n=channel number)
cc =	Control number
vv =	Value
F7H =	End of Exclusive

Control	0n	ccH	vvH
Split Point	Always 00H	14H	14H : Split Key Num-
			ber
Metronome	Always 00H	1BH	00H : off
			01H	: –
			02H	: 2/4
			03H	: 3/4
			04H	: 4/4
			05H	: 5/4
			06H	: 6/4
			7FH : No accent
Damper Level	ch: 00H-0FH	3DH(Sets the Damper Level
			for each channel)
			00H-7FH
Channel Detune ch: 00H-0FH		43H (Sets the Detune value
			for each channel)
			00H-7FH
Voice Reserve	ch: 00H-0FH	45H	00H : Reserve off 7FH
			: on*

*When Volume, Expression is received for Reserve On, they will be effective from the next Key On. Reserve Off is normal.

11.SYSTEM EXCLUSIVE MESSAGES (Others)

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]

-> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously changes the pitch of all channels.

F0H =	Exclusive Status
43H =	Yamaha ID
1nH =	When received, n=0~F.
	When transmitted, n=0.
27H =	Model ID of TG100
30H =	Sub ID
00H	=
00H	=
mmH = Master Tune MSB
llH =	Master Tune LSB

CLP-F01Appendix 71