Manuals
/
Brands
/
Computer Equipment
/
Personal Computer
/
Yamaha
/
Computer Equipment
/
Personal Computer
Yamaha
CRW2200S manual
1
1
75
75
Download
75 pages, 2.29 Mb
Contents
Page
Page
Page
Page
SAFETY PRECAUTIONS
Page
■About CD-R/RWdiscs
■Precautions for Transportation
■Copyrights
■WARRANTY
Table of Contents
For SCSI Connection
For IDE Connection
Introduction
●Generous 8MB of buffer memory
●Buffer Underrun Protection
●Optimum Write Speed Control
●Running OPC (Optimum Power Control)
Buffer Underrun Defined
Yamaha Buffer Underrun Protection
Before Use
PC/AT-CompatibleComputer
Operating System (OS)
CD Writing Software
Hard Drive Space
CD-Rdiscs*1
CD-RWdiscs*2
High Speed CD-RWdiscs*3
About CD-ROMs
About Partial CAV (Constant Angular Velocity)
About 10X-speedwriting/rewriting of a High Speed CD-RWdisc
Serial No
Front and Rear of Unit
➀Jumper switch
➁SCSI INTERFACE connector
➂DC IN connector (The SCSI convertor’s side)
➃DIGITAL AUDIO OUT connector
➄ANALOG AUDIO OUT connector
➀DIGITAL AUDIO OUT connector
➁ANALOG AUDIO OUT connector
➂Jumper switch
➃IDE INTERFACE CONNECTOR
➄DC INPUT connector
SCSI Connection Set Up
Connecting the CRW2200S (→P. 14 – 29)
STEP Configuring for the Operating 2 System (→P. 30, 31)
STEP Installing the CD Writing 3 Software
STEP Start Using the CRW2200S
Opening the Computer
1Shut down your computer and unplug it from the AC outlet
Page
Audio cable connection
4Connect the audio cable to the CRW2200 drive. (If necessary)
Connecting the analog audio cable
Connecting the digital audio cable
Installing the SCSI Convertor to the CRW2200 drive
5Attach the SCSI convertor (included) to the rear of the CRW2200 drive
6Secure the SCSI convertor to the CRW2200 drive with the screw (included)
Page
Page
➀SCSI ID Number
➁Parity Check
➂Termination
➃Block Size
Choosing the Connection Method
9The CRW2200S can be used as a supplemental drive or as a replacement drive
As a supplemental drive
As a replacement drive
Installing the CRW2200S
10As a supplemental drive
Connect the
13Connect the audio cable to the sound card
Page
17Reconnect the computer to the AC outlet and turn it on
Configuring for the Operating System
Double-click
Installing the CD Writing Software
20Install the CD writing software
Removing the SCSI convertor
5Remove the screw securing the SCSI convertor to the CRW2200 drive
6Remove the SCSI convertor from the CRW2200 drive
7Disconnect the power cable from the SCSI convertor and the CRW2200 drive
E-IDE(ATAPI) Connection Set Up
STEP Does your computer have a SCSI
Remove the SCSI
1 connection with the drive
YES convertor. (→P. 32 – 34)
STEP Connecting the CRW2200E 2 (→P. 37 – 46)
Page
Page
About IDE
Typical IDE-typehardware installation
Connecting examples
Example-1:As secondary slave (For supplemental drive)
Example-2:As secondary master
(For replacing your existing drive with the unit)
Page
Page
Installing the CRW2200E
6As an supplemental drive:
As a replacement drive:
(→P. 26 step 11)
8Connect the IDE cable
9Connect the audio cable. (If necessary)
Page
Connect a
13Reconnect the computer to the AC outlet and turn it on. (→P. 29 step 17)
Page
About DMA Settings (Setting of Transfer Mode)
About DMA
16Install the CD writing software
Operation
1Shut down the computer
Find a
Push the tool gently into the Manual Eject hole until the
4Turn on your computer to close the disc tray
Troubleshooting
The CRW2200E is not recognized. (In the case of E-IDE(ATAPI) connection)
The disc tray does not open
The disc keeps being ejected
The drive does not operate correctly
No sound of CD-DA(audio CD) disc is audible
1The “Properties” setting of the CRW2200S
2The setting of the Windows Media Player
The “Buffer Underrun” error message is displayed
Other problems
Appendix
Session-at-Once(SAO)
Packet Writing
URL for YAMAHA CD-R/RWDrives web sites:
Supported Formats
Page
Page
The CRW2200 series complies with the following specifications
Symbols
Page
EUROPE, EASTERN EUROPE and
RUSSIA
U.S.A
CANADA
AUSTRALIA