Rear Panel without the Scsi Convertor | Yamaha CRW2200S guide

Front and Rear of Unit

Rear Panel (without the SCSI Convertor)

➀ ➁

➂

➃

➄

➀DIGITAL AUDIO OUT connector

If your sound card has a SPDIF (digital audio) input connector, you can connect the DIGITAL AUDIO OUT connector of the unit to the SPDIF connector using a digital audio cable (sold separately). (→P. 17, 45)

➁ANALOG AUDIO OUT connector

Connect one end of the 4-pin audio cable to this and the other end to your computer’s sound card or built-in audio. (→P. 16, 44)

➂Jumper switch

Plug a plastic shunt into this jumper switch to select the connection, either IDE master or slave. The CRW2200 drive’s factory setting is SLAVE. ( →P. 42)

➃IDE INTERFACE CONNECTOR

Insert the connector of the IDE cable here. (→P. 43)

➄DC INPUT connector

Insert the power connector from your computer’s power supply in this socket to feed power to the drive. (→P. 46)

11

Image 19

Yamaha CRW2200S manual Rear Panel without the Scsi Convertor, ➀ Digital Audio OUT connector, ➁ Analog Audio OUT connector

Contents

Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Introduction Features of the CRW2200 drive Yamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection High Speed CD-RW discs*3 Supported DiscsCD-R discs*1 CD-RW discs*2 About Partial CAV Constant Angular Velocity About CD-ROMs About 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial Number Front Panel Front and Rear of Unit Rear Panel with the Scsi Convertor ➄ DC Input connector ➀ Digital Audio OUT connector➁ Analog Audio OUT connector ➂ Jumper switch Long-Nosed Pliers Scsi Connection Set UpTools Phillips Screwdriver Scsi Connection Set Up CRW2200S Setup Flowchart Cover Front panel Connecting the CRW2200SOpening the Computer Shut down your computer and unplug it from the AC outlet Discharge any static charge Left L Ground G Right R Audio cable To Sound card Connecting the analog audio cableAudio cable connection Connect the audio cable to the CRW2200 drive. If necessary Ground G Signal D Digital audio cable To Sound card Connecting the digital audio cable Screw Installing the Scsi Convertor to the CRW2200 drive DC Input Yellow wire Jumper switches Setting the Jumper SwitchesRear Panel Scsi ID ➀ Scsi ID Number ➂ Termination ➁ Parity Check Workstation Block size OFF Default Block size onSet to on when installing ➃ Block Size Choosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Motherboard Colored line connector Scsi connector 50-pin Scsi flat cable Spdif Digital audio cable Sound card Top Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating System Install the CD writing software Installing the CD Writing Software Removing the Scsi convertor Removing the Scsi convertor Removing the Scsi convertor Audio cable Pin Scsi flat cable Pin power cable Remove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup Flowchart Connecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Example-1 As secondary slave For supplemental drive Connecting examples IDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switch As an supplemental drive Installing the CRW2200E Connect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Yamaha CD-R/RW Drives web site URL Europe Troubleshooting Troubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200S Buffer Underrun error message is displayed Track-at-Once TAO AppendixWriting Modes Disc-at-Once DAO Packet Writing Session-at-Once SAOAppendix URL for Yamaha CD-R/RW Drives web sites Europe About firmware Status Ndicator essages LED olor LED Indicator Messages CD-RW CRW2200 drive CRW2200 series complies with the following specifications Index Symbols Phillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe