Connecting the digital audio cable | Yamaha CRW2200S manual

SCSI Connection Set Up

Connecting the digital audio cable

The digital connection for the CRW2200S is ideal for pure quality audio playback, outputting digital signals recorded on CDs to the sound card without any distortion.

Examples of the digital connection

To output digital audio signals to external devices, you must use the digital connection to connect the unit and the sound card. With this connection you can:

•Enjoy music using a digital audio amplifier.

•Record music digitally with an MD player.

Connect the digital audio cable to the DIGITAL AUDIO OUT connector on the rear panel of the CRW2200 drive, making sure of the connector’s direction.

DIGITAL AUDIO

OUT

Ground (G)

Signal (D)

Digital audio cable

(to Sound card)

Note

For the digital connection, you need a digital audio cable with appropriate connectors, and a sound card with SPDIF (digital audio) input connectors.

17

Image 25

Yamaha CRW2200S manual Connecting the digital audio cable, Ground G Signal D Digital audio cable To Sound card

Contents

Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents → E-IDE Atapi Connection Set Up P → Scsi Connection Set Up PScsi convertor Introduction Features of the CRW2200 drive Yamaha Buffer Underrun Protection Buffer Underrun DefinedIntroduction System Requirements Before UseThese are also required for Scsi connection CD-R discs*1 Supported DiscsCD-RW discs*2 High Speed CD-RW discs*3 About Partial CAV Constant Angular Velocity About CD-ROMs About 10X-speed writing/rewriting of a High Speed CD-RW disc Serial number Letters and 7 digits Serial Number Front Panel Front and Rear of Unit Rear Panel with the Scsi Convertor ➁ Analog Audio OUT connector ➀ Digital Audio OUT connector➂ Jumper switch ➄ DC Input connector Tools Scsi Connection Set UpPhillips Screwdriver Long-Nosed Pliers Scsi Connection Set Up CRW2200S Setup Flowchart Opening the Computer Connecting the CRW2200SShut down your computer and unplug it from the AC outlet Cover Front panel Discharge any static charge Audio cable connection Connecting the analog audio cableConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound card Ground G Signal D Digital audio cable To Sound card Connecting the digital audio cable Screw Installing the Scsi Convertor to the CRW2200 drive DC Input Yellow wire Jumper switches Setting the Jumper SwitchesRear Panel Scsi ID ➀ Scsi ID Number ➂ Termination ➁ Parity Check Set to on when installing Block size OFF Default Block size on➃ Block Size Workstation Choosing the Connection Method As a replacement driveCD-ROM drive Audio cable Pin IDE cable Pin power cable Installing the CRW2200SInch drive bay slot Front cover Motherboard Colored line connector Scsi connector 50-pin Scsi flat cable Spdif Digital audio cable Sound card Top Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on For Windows NT Configuring for the Operating System Install the CD writing software Installing the CD Writing Software Removing the Scsi convertor Removing the Scsi convertor Removing the Scsi convertor Audio cable Pin Scsi flat cable Pin power cable Remove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up IDE Atapi Connection Set Up CRW2200E Setup Flowchart Connecting the CRW2200E Choosing the Connection Method About IDE Typical IDE-type hardware installationSlave Motherboard Primary Master Secondary SlaveMaster Example-1 As secondary slave For supplemental drive Connecting examples IDE Atapi Connection Set Up Rear Panel Master Slave factory setting About the Csel jumper switch As an supplemental drive Installing the CRW2200E Connect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Loading a Disc OperationEjecting a Disc Operation Ejecting a Disc in an EmergencyManual Eject hole Paper Clip Yamaha CD-R/RW Drives web site URL Europe Troubleshooting Troubleshooting Disc keeps being ejected Setting of the Windows Media Player Properties setting of the CRW2200S Buffer Underrun error message is displayed Writing Modes AppendixDisc-at-Once DAO Track-at-Once TAO Packet Writing Session-at-Once SAOAppendix URL for Yamaha CD-R/RW Drives web sites Europe About firmware Status Ndicator essages LED olor LED Indicator Messages CD-RW CRW2200 drive CRW2200 series complies with the following specifications Index Symbols Phillips Screwdriver 12, 32 Russia EUROPE, Eastern Europe