Yamaha CRW2200S Connect the

SCSI Connection Set Up

The following explains how to add the drive to the computer as illustrated.

If you are replacing the existing CD-ROM drive, the procedure is basically the same.

Note

The way of installing built-in devices may differ, depending on the computer. Refer also to the documentation that came with your computer.

11Slide the drive backwards into the slot, then tighten the four fastening screws on the sides of the unit to hold the drive in place.

Notes

•Do not apply excessive force when sliding the drive backwards into the drive bay slot.

•Leave enough room behind the drive to connect the power, SCSI, and audio cables.

12Connect the 50-pin SCSI flat cable to the computer’s SCSI card and to the SCSI INTERFACE connector on the rear panel of the CRW2200S. Be sure to plug in the cable so that the colored line on the cable corresponds to the pin 1 on the right end of the connector as shown in the figure below. The pin 1 of the CRW2200S is positioned in the right part of the SCSI connector. The pin 1 of the SCSI connector is labeled on the SCSI card, or refer to the documentation that came with your SCSI card.

Motherboard

SCSI INTERFACE

Colored line connector

Colored line

SCSI connector 50-pin SCSI flat cable

26

Contents

Page Page Page Page SAFETY PRECAUTIONS Page ■About CD-R/RWdiscs ■Precautions for Transportation ■Copyrights ■WARRANTY Table of Contents For SCSI Connection For IDE Connection Introduction ●Generous 8MB of buffer memory ●Buffer Underrun Protection ●Optimum Write Speed Control ●Running OPC (Optimum Power Control) Buffer Underrun Defined Yamaha Buffer Underrun Protection Before Use PC/AT-CompatibleComputer Operating System (OS) CD Writing Software Hard Drive Space CD-Rdiscs*1 CD-RWdiscs*2 High Speed CD-RWdiscs*3 About CD-ROMs About Partial CAV (Constant Angular Velocity) About 10X-speedwriting/rewriting of a High Speed CD-RWdisc Serial No Front and Rear of Unit ➀Jumper switch ➁SCSI INTERFACE connector ➂DC IN connector (The SCSI convertor’s side) ➃DIGITAL AUDIO OUT connector ➄ANALOG AUDIO OUT connector ➀DIGITAL AUDIO OUT connector ➁ANALOG AUDIO OUT connector ➂Jumper switch ➃IDE INTERFACE CONNECTOR ➄DC INPUT connector SCSI Connection Set Up Connecting the CRW2200S (→P. 14 – 29) STEP Configuring for the Operating 2 System (→P. 30, 31) STEP Installing the CD Writing 3 Software STEP Start Using the CRW2200S Opening the Computer 1Shut down your computer and unplug it from the AC outlet Page Audio cable connection 4Connect the audio cable to the CRW2200 drive. (If necessary) Connecting the analog audio cable Connecting the digital audio cable Installing the SCSI Convertor to the CRW2200 drive 5Attach the SCSI convertor (included) to the rear of the CRW2200 drive 6Secure the SCSI convertor to the CRW2200 drive with the screw (included) Page Page ➀SCSI ID Number ➁Parity Check ➂Termination ➃Block Size Choosing the Connection Method 9The CRW2200S can be used as a supplemental drive or as a replacement drive As a supplemental drive As a replacement drive Installing the CRW2200S 10As a supplemental drive Connect the 13Connect the audio cable to the sound card Page 17Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System Double-click Installing the CD Writing Software 20Install the CD writing software Removing the SCSI convertor 5Remove the screw securing the SCSI convertor to the CRW2200 drive 6Remove the SCSI convertor from the CRW2200 drive 7Disconnect the power cable from the SCSI convertor and the CRW2200 drive E-IDE(ATAPI) Connection Set Up STEP Does your computer have a SCSI Remove the SCSI 1 connection with the drive YES convertor. (→P. 32 – 34) STEP Connecting the CRW2200E 2 (→P. 37 – 46) Page Page About IDE Typical IDE-typehardware installation Connecting examples Example-1:As secondary slave (For supplemental drive) Example-2:As secondary master (For replacing your existing drive with the unit) Page Page Installing the CRW2200E 6As an supplemental drive: As a replacement drive: (→P. 26 step 11) 8Connect the IDE cable 9Connect the audio cable. (If necessary) Page Connect a 13Reconnect the computer to the AC outlet and turn it on. (→P. 29 step 17) Page About DMA Settings (Setting of Transfer Mode) About DMA 16Install the CD writing software Operation 1Shut down the computer Find a Push the tool gently into the Manual Eject hole until the 4Turn on your computer to close the disc tray Troubleshooting The CRW2200E is not recognized. (In the case of E-IDE(ATAPI) connection) The disc tray does not open The disc keeps being ejected The drive does not operate correctly No sound of CD-DA(audio CD) disc is audible 1The “Properties” setting of the CRW2200S 2The setting of the Windows Media Player The “Buffer Underrun” error message is displayed Other problems Appendix Session-at-Once(SAO) Packet Writing URL for YAMAHA CD-R/RWDrives web sites: Supported Formats Page Page The CRW2200 series complies with the following specifications Symbols Page EUROPE, EASTERN EUROPE and RUSSIA U.S.A CANADA AUSTRALIA