Table of Contents | Yamaha CRW2200S specs

Table of Contents
SCSI connection and E-IDE (ATAPI) connection	.............................. 1
Introduction	2
Features of the CRW2200 drive	2
Before Use	4
System Requirements	4
Supported Discs	5
Serial Number	8
Front and Rear of Unit	9
Front Panel	9
Rear Panel (with the SCSI Convertor)	10
Rear Panel (without the SCSI Convertor)	11
SCSI Connection Set Up	12
Tools	12
CRW2200S Setup Flowchart	13
Connecting the CRW2200S	14
Removing the SCSI convertor	32
Tools	32
Removing the SCSI convertor	32
E-IDE (ATAPI) Connection Set Up	35
Tools	35
CRW2200E Setup Flowchart	36
Connecting the CRW2200E	37
Operation	50
Loading a Disc	50
Ejecting a Disc	50
Ejecting a Disc in an Emergency	51
Troubleshooting	52
Appendix	57
Writing Modes	57
About firmware	59
LED Indicator Messages	60
CRW2200 Specifications	60
Index	64

©2001 YAMAHA CORPORATION. All Rights Reserved.

This document may not, in whole or in part, be copied, photocopied, reproduced, translated, transmitted, or reduced to any electronic medium of machine readable form without prior consent in writing from Yamaha.

Windows is a registered trademark of Microsoft Corporation. UNIX is a registered trademark of UNIX System Laboratories. SafeBurn™ is a trademark of Yamaha Corporation.

All other trademarks are the property of their respective companies.

v

Image 8

Yamaha CRW2200S manual Table of Contents

Contents

Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents Scsi convertor → Scsi Connection Set Up P→ E-IDE Atapi Connection Set Up P Features of the CRW2200 drive Introduction Introduction Buffer Underrun DefinedYamaha Buffer Underrun Protection These are also required for Scsi connection Before UseSystem Requirements Supported Discs CD-R discs*1CD-RW discs*2 High Speed CD-RW discs*3 About CD-ROMs About Partial CAV Constant Angular Velocity About 10X-speed writing/rewriting of a High Speed CD-RW disc Serial Number Serial number Letters and 7 digits Front and Rear of Unit Front Panel Rear Panel with the Scsi Convertor ➀ Digital Audio OUT connector ➁ Analog Audio OUT connector➂ Jumper switch ➄ DC Input connector Scsi Connection Set Up ToolsPhillips Screwdriver Long-Nosed Pliers CRW2200S Setup Flowchart Scsi Connection Set Up Connecting the CRW2200S Opening the ComputerShut down your computer and unplug it from the AC outlet Cover Front panel Discharge any static charge Connecting the analog audio cable Audio cable connectionConnect the audio cable to the CRW2200 drive. If necessary Left L Ground G Right R Audio cable To Sound card Connecting the digital audio cable Ground G Signal D Digital audio cable To Sound card Installing the Scsi Convertor to the CRW2200 drive Screw Yellow wire DC Input Rear Panel Setting the Jumper SwitchesJumper switches ➀ Scsi ID Number Scsi ID ➁ Parity Check ➂ Termination Block size OFF Default Block size on Set to on when installing➃ Block Size Workstation CD-ROM drive As a replacement driveChoosing the Connection Method Inch drive bay slot Front cover Installing the CRW2200SAudio cable Pin IDE cable Pin power cable Colored line connector Scsi connector 50-pin Scsi flat cable Motherboard Digital audio cable Sound card Spdif Top Bottom Power cable Pin power cable Reconnect the computer to the AC outlet and turn it on Configuring for the Operating System For Windows NT Installing the CD Writing Software Install the CD writing software Removing the Scsi convertor Removing the Scsi convertor Audio cable Pin Scsi flat cable Pin power cable Removing the Scsi convertor Remove the Scsi convertor from the CRW2200 drive IDE Atapi Connection Set Up CRW2200E Setup Flowchart IDE Atapi Connection Set Up Connecting the CRW2200E Choosing the Connection Method Slave Motherboard Primary Master Secondary SlaveMaster Typical IDE-type hardware installationAbout IDE Connecting examples Example-1 As secondary slave For supplemental drive IDE Atapi Connection Set Up About the Csel jumper switch Rear Panel Master Slave factory setting Installing the CRW2200E As an supplemental drive Connect the audio cable. If necessary Ground G Signal D Digital audio cable Top DC Input connector Bottom Pin power cable Configuring for the Operating System About DMA Settings Setting of Transfer Mode About DMA Ejecting a Disc OperationLoading a Disc Manual Eject hole Paper Clip Ejecting a Disc in an EmergencyOperation Troubleshooting Yamaha CD-R/RW Drives web site URL Europe Troubleshooting Disc keeps being ejected Properties setting of the CRW2200S Setting of the Windows Media Player Buffer Underrun error message is displayed Appendix Writing ModesDisc-at-Once DAO Track-at-Once TAO Appendix Session-at-Once SAOPacket Writing About firmware URL for Yamaha CD-R/RW Drives web sites Europe LED Indicator Messages Status Ndicator essages LED olor CD-RW CRW2200 drive CRW2200 series complies with the following specifications Symbols Index Phillips Screwdriver 12, 32 EUROPE, Eastern Europe Russia