RedMax SGCZ2401S-CA manual Starting the Engine, Using the Product

Page 14

English

5. For safe operation

IMPORTANT

Remove any obstacle before beginning work.

3.Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened.

4.Be sure the debris guard is firmly attached in place.

5.Always use the shoulder strap. Adjust the strap for comfort before starting the engine. The strap should be adjusted so the left hand can comfortably hold the handlebar grip approximately waist high.

■STARTING THE ENGINE

1.Keep bystanders and animals at least 50feet (15m) away from the operating point. If you are approached, immediately stop the engine.

2.The product is equipped with a centrifugal clutch mechanism, so the cutting attachment could rotate as soon as the engine is started. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts.

WARNING

Make sure the throttle is at idle position.

Never place the throttle into the high speed position or half throttle position (throttle lock position) when starting the engine.

3.After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position (idle position). If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair.

■USING THE PRODUCT

IMPORTANT

Cut only materials recommended by the manufacturer. And use only for tasks explained in the manual.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents
SGCZ2401S SGCZ2401S-CA Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido SGCZ2401S/SGCZ2401S-CA SpecificationsParts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Machine Wear head, eye and ear protectionImportante Emission Control Symbols on the machinePosition SGCZ2401SControl DE Emisiones EmplacementPosición Working Circumstance For safe operationWorking Condition Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineUtilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoTransportation Handling FuelRefill after cooling the engine Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoSet up Assemblage Montaje Cuttercase Locking holes SE4 SE5 SE6Cuttercase SE4 Blade GuardCouvert de lame Trous de verrouillage Assemblage MontajePORTE-LAME SE4 Cabezal DE Corte SE4 Bastidor del cortador cuter Orificios de bloqueoRecommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Cutting head will start rotating upon the engine starts OperationOP1 OP2 OP3 OP4 Starting Engine Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador UtilisationHOW to USE OP7Forma DE UTILIZAClÓN OP9 OP8Cutting Work Recommended ApplicationsApplications Recommandées Aplicaciones RecomendadasMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoBlade To install bladesMA1 MA2 MA3 To Sharpen bladeCuchilla Entretien MantenimientoLame AIR Filter Replacement Plug is a NGK CMR7HMA4 MA5 MA6 Fuel FilterBougie D’ALLUMAGE Filtre a CarburantFiltro DE Combustible Couple DE SerrageGearcase and Cuttercase MA8 MA7 MA8Spark Arrester MA7 Intake AIR Cooling VentOuïe DU Refroidissement PAR AIR PARE-ETINCELLES MA7 Parachispas MA7LE Couvert DE Courroie ET DE Lame MA8 Bastidor DE Engranajes Y Bastidor DEL Cortador MA8Disposal Procedures to be Performed After Every 100 Hours of USEStorage MA9Mise au rebut Eliminación Procedure a Effectuer Toutes LES Heures D’UTILISATIONRangement Almacenamiento Procedimientos a Realizar Cada 100 Horas DE USOGuide de localisation des pannes Troubleshooting guide12. Guía de localización y solución de problemas Reciprocators NotaParts list SGCZ2401S/SGCZ2401S-CA SGCZ2401S/SGCZ2401S-CA Engine Unit S/N 60100101 and up Part Number Description Qty Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Zenoah AMERICA, INC