RedMax SGCZ2401S-CA manual Storage, Disposal, MA9

Page 46

English

9. Maintenance

MA9	(1)

(2)

MA10

the cylinder.

IMPORTANT

•If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the machine. (MA9)

(1)cylinder

(2)intake air cooling vent (back)

■PROCEDURES TO BE PERFORMED AFTER

EVERY 100 HOURS OF USE

1.Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.

2.Tighten all screws, bolts, and fittings.

3.Check to see if any oil or grease has worked its way in between the clutch lining and drum, and if it has wipe it away using oil-free, lead-free gasoline.

English

10. Storage

•Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.

•Oil the blades.

English

11. Disposal

•When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.

46

Image 46

Contents SGCZ2401S SGCZ2401S-CA Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsSGCZ2401S/SGCZ2401S-CA Fiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Machine Wear head, eye and ear protectionImportante Emission Control Symbols on the machinePosition SGCZ2401SPosición EmplacementControl DE Emisiones Working Condition For safe operationWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoSet up Assemblage Montaje Cuttercase Locking holes SE4 SE5 SE6Cuttercase SE4 Blade GuardCouvert de lame Trous de verrouillage Assemblage MontajePORTE-LAME SE4 Cabezal DE Corte SE4 Bastidor del cortador cuter Orificios de bloqueoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda OP1 OP2 OP3 OP4 Starting Engine OperationCutting head will start rotating upon the engine starts Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador UtilisationHOW to USE OP7Forma DE UTILIZAClÓN OP9 OP8Cutting Work Recommended ApplicationsApplications Recommandées Aplicaciones RecomendadasMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoBlade To install bladesMA1 MA2 MA3 To Sharpen bladeLame Entretien MantenimientoCuchilla AIR Filter Replacement Plug is a NGK CMR7HMA4 MA5 MA6 Fuel FilterBougie D’ALLUMAGE Filtre a CarburantFiltro DE Combustible Couple DE SerrageGearcase and Cuttercase MA8 MA7 MA8Spark Arrester MA7 Intake AIR Cooling VentOuïe DU Refroidissement PAR AIR PARE-ETINCELLES MA7 Parachispas MA7LE Couvert DE Courroie ET DE Lame MA8 Bastidor DE Engranajes Y Bastidor DEL Cortador MA8Disposal Procedures to be Performed After Every 100 Hours of USEStorage MA9Mise au rebut Eliminación Procedure a Effectuer Toutes LES Heures D’UTILISATIONRangement Almacenamiento Procedimientos a Realizar Cada 100 Horas DE USO12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Reciprocators NotaParts list SGCZ2401S/SGCZ2401S-CA SGCZ2401S/SGCZ2401S-CA Engine Unit S/N 60100101 and up Part Number Description Qty Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Zenoah AMERICA, INC