Dolmar MS-22C instruction manual Checking the spark plug, Supply of grease to gear case

Page 16

Checking the spark plug

– Only use the supplied universal wrench to remove or to install the spark plug.

– The gap between the two electrodes of the spark plug should be 0.6 - 0.7 mm (0.024" - 0.028"). If the gap is too wide or too narrow, adjust it. If the spark plug is clogged with carbon or fouled, clean it thoroughly or replace it.

CAUTION: Never touch the spark plug connector while the engine is running

(danger of high voltage electric shock).

0.6mm-0.7mm

 

 

(0.024”-0.028”)

Supply of grease to gear case

Supply grease (Shell Alvania 3 or equivalent) to the gear case through the grease hole every 30 hours. (Genuine DOLMAR grease may be purchased from your DOLMAR dealer.)

Suction head in the fuel tank

– The felt filler (1) of the suction head is used to filler the fuel required by the

 

carburetor.

 

– A periodical visual inspection of the felt filter is to be conducted. For that

 

purpose open the tank cap, use a wire hook and pull out the suction head

 

through the tank opening. Filters found to have hardened, been polluted or

 

clogged up are to be replaced.

 

– Insufficient fuel supply can result in the admissible maximum speed being

 

exceeded. It is therefore important to replace the felt filter at least quarterly

 

to ensure satisfactory fuel supply to the carburetor.

(1)

 

Gear case

Grease hole

Cleaning of muffler exhaust port

Check of muffler exhaust port (2) regularly.

If it is clogged by carbon deposits, carefully scratch the deposits out with a suitable tool.

(2)

Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

16

Image 16
Contents MS-22C Symbols EnglishSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentRefueling MetersMaintenance instructions Method of operationCutting Tools First AidSpecification Model MS-22CMS-22C String Trimmer Designation of PartsMounting of Handle Assembly of Engine and ShaftFor machine with Loop handle Mounting of Protector Mounting of Nylon Cutter Head FUELS/REFUELING Handling fuelFuel and oil mixture Check points before operationCorrect Handling of Machine Putting Into OperationIdle Adjustment Nylon Cutting HeadStarting the warm engine Checking the Idling speedPage Cleaning of air cleaner Daily checkup and maintenanceServicing Instructions Cleaning of muffler exhaust port Checking the spark plugSupply of grease to gear case Suction head in the fuel tankFault location Maintenance scheduleStorage Emisson Compliance Period Obtaining Warranty Service HOW to Make a Claim Symboles FrançaisConsignes DE Sécurité Instructions généralesUtilisation spéciale de la machine Équipement personnel de protectionRavitaillement MètresInstructions de maintenance Méthode d’utilisationTête de coupe à fill Premier secourCaracteristiques Techniques MS-22CMS-22C Taille-bordures Nomenclature DES PiècesAssemblage DU Mouteur ET DE L’ARBRE Montage DE LA PoignéeMontage DU Dispositif DE Protection Montage DE LA Tête DE Coupe À FIL CARBURANTS/RAVITAILLEMENT Stockage du carburantManipulation Correcte DE LA Machine Mise EN MarcheRéglage DU Ralenti Tête DE Coupe À FIL EN NylonRemplacement du fil en nylon Instructions Relatives AUX Réparations Contrôle et opérations de maintenance réguliersNettoyage du filtre à air Contôle de la bougie d’allumage Graissage du carter d’engrenageTête d’aspiration dans le réservoir de carburant Nettoyage de l’orifice du pot d’échappementRemisage Plan de maintenanceLocalisation des défauts Símbolos SpanishInstrucciones DE Seguridad Instrucciones generalesMetros Método de trabajo Herramientas de CorteInstrucciones de mantenimiento Primeros AuxiliosEspecificación Modelo MS-22CMS-22C Cortabordes Denominación DE PartesMontaje DEL Manillar Montaje DE Motor Y EJEPara maquinas con manubrio en bucle Montaje DEL Protector Montaje DE LA Cabezal DE Corte DE Nylon COMBUSTIBLES/REABASTECIMIENTO USO Correcto DE LA Máquina Puesta EN MarchaCabezal DE Nylon Precauciones durante la operaciónArranque del motor en caliente Comprobar la velocidad en vacioSustitución de la cuerda de nylon Comprobación y mantenimiento diarios Instrucciones DE ServicioLimpieza del filtro de aire Comprobación de la Bujía Suministro de grasa a la caja de engranajesCabezal de succión en el tanque de combustible Limpieza del orificio de salida del silenciadorEsquema de mantenimiento AlmacenamientoLocalizacion de averias Dolmar GmbH Postfach 70 04 Hamburg Germany 6199521201