Dolmar MS-22C Method of operation, Cutting Tools, Maintenance instructions, First Aid

Page 5

Method of operation

Only use the string trimmer in good lighting and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing.

Never cut above the waist height.

Never stand on a ladder and run the string trimmer.

Never climb up trees to perform cutting operation with the string trimmer.

Never work on unstable surfaces.

Remove sand, stones, nails etc. found within the working range. Foreign particles may damage the nylon cutting head and can cause dangerous kick-backs.

Before commencing cutting, the nylon cutting head must have reached full working speed.

Cutting Tools

Employ only the correct nylon cutting head for the job in hand.

For cutting thick materials, such as weed, high grass, bushes, shrubs, underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work by swinging the string trimmer evenly in half-circles from right to left (similar to using a scythe).

Maintenance instructions

The condition of the trimmer also of the shoulder strap must be checked before commencing work.

Turn off the engine and remove the spark plug connector when replacing, and also when cleaning the nylon cutting head.

Operate the string trimmer with as little noise and contamination as possible. In particular, check the correct setting of the carburetor.

Clean the string trimmer at regular intervals and check that all screws and nuts are well tightened.

Never service or store the string trimmer in the vicinity of naked flames.

Always store the string trimmer in locked rooms and with an emptied fuel tank.

Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies.

Do not perform any modifications on the string trimmer as this will endanger your safety.

The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All the other work is to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by DOLMAR.

Use of non-approved accessories and tools means increased risk of accidents.

DOLMAR will not accept any liability for accidents or damage caused by the use of non-approved nylon cutting heads and fixing devices of nylon cutting heads, or accessories.

First Aid

In case of accident, make sure that a first-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the first aid box.

When asking for help, please give the following information:

Place of accident

What happened

Number of injured persons

Kind of injuries

Your name

5

Image 5
Contents MS-22C English SymbolsGeneral Instructions Safety InstructionsIntended use of the machine Personal protective equipmentMeters RefuelingMethod of operation Maintenance instructionsCutting Tools First AidModel MS-22C SpecificationDesignation of Parts MS-22C String TrimmerFor machine with Loop handle Assembly of Engine and ShaftMounting of Handle Mounting of Protector Mounting of Nylon Cutter Head Handling fuel FUELS/REFUELINGFuel and oil mixture Check points before operationPutting Into Operation Correct Handling of MachineNylon Cutting Head Idle AdjustmentStarting the warm engine Checking the Idling speedPage Servicing Instructions Daily checkup and maintenanceCleaning of air cleaner Checking the spark plug Cleaning of muffler exhaust portSupply of grease to gear case Suction head in the fuel tankStorage Maintenance scheduleFault location Emisson Compliance Period Obtaining Warranty Service HOW to Make a Claim Français SymbolesInstructions générales Consignes DE SécuritéUtilisation spéciale de la machine Équipement personnel de protectionMètres RavitaillementMéthode d’utilisation Instructions de maintenanceTête de coupe à fill Premier secourMS-22C Caracteristiques TechniquesNomenclature DES Pièces MS-22C Taille-borduresMontage DE LA Poignée Assemblage DU Mouteur ET DE L’ARBREMontage DU Dispositif DE Protection Montage DE LA Tête DE Coupe À FIL Stockage du carburant CARBURANTS/RAVITAILLEMENTMise EN Marche Manipulation Correcte DE LA MachineTête DE Coupe À FIL EN Nylon Réglage DU RalentiRemplacement du fil en nylon Nettoyage du filtre à air Contrôle et opérations de maintenance réguliersInstructions Relatives AUX Réparations Graissage du carter d’engrenage Contôle de la bougie d’allumageTête d’aspiration dans le réservoir de carburant Nettoyage de l’orifice du pot d’échappementLocalisation des défauts Plan de maintenanceRemisage Spanish SímbolosInstrucciones generales Instrucciones DE SeguridadMetros Herramientas de Corte Método de trabajoInstrucciones de mantenimiento Primeros AuxiliosModelo MS-22C EspecificaciónDenominación DE Partes MS-22C CortabordesPara maquinas con manubrio en bucle Montaje DE Motor Y EJEMontaje DEL Manillar Montaje DEL Protector Montaje DE LA Cabezal DE Corte DE Nylon COMBUSTIBLES/REABASTECIMIENTO Puesta EN Marcha USO Correcto DE LA MáquinaPrecauciones durante la operación Cabezal DE NylonArranque del motor en caliente Comprobar la velocidad en vacioSustitución de la cuerda de nylon Limpieza del filtro de aire Instrucciones DE ServicioComprobación y mantenimiento diarios Suministro de grasa a la caja de engranajes Comprobación de la BujíaCabezal de succión en el tanque de combustible Limpieza del orificio de salida del silenciadorLocalizacion de averias AlmacenamientoEsquema de mantenimiento Dolmar GmbH Postfach 70 04 Hamburg Germany 6199521201