Dolmar MS-22C Assembly of Engine and Shaft, Mounting of Handle, For machine with Loop handle

Page 8

ASSEMBLY OF ENGINE AND SHAFT

CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. Always wear protective gloves.

CAUTION: Start the string trimmer only after having assembled it completely.

Insert the drive shaft into the holder case (Fig).

Note: Always insert the drive shaft into the Clutch case fully (approx. 58 mm). If the inner shaft resists full insertion of the drive shaft, try to insert it again after slightly rotating the drive shaft or the support washer on the gear case to match the inner shaft to the hole inside the holder case.

After making sure that the drive shaft is installed fully and properly, tighten the socket head bolt (M5 x 14) and socket head bolt (M5 x 25) to secure the drive shaft.

–Inset control cable (1) through adjusting cable (2) and fit nipple of control cable into swivel (3) of carburetor.

Connect the switch cords to the two cords from the engine by inserting one into the other.

Fix the cord connector by clamp.

Clutch case

Socket

Socket

Drive shaft

head bolt

head bolt

 

(M5 x 14)

(M5 x 25)

 

 

 

 

 

 

 

Connectors

MOUNTING OF HANDLE

CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. Always wear protective gloves.

CAUTION: Start the string trimmer only after having assembled it completely.

For machine with Loop handle

Do not adjust position of the loop handle too close to the control grip

–The standard position of the handle is 200mm to 250mm from the hanger.

to engine

8

Image 8
Contents MS-22C Symbols EnglishSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentRefueling MetersMaintenance instructions Method of operationCutting Tools First AidSpecification Model MS-22CMS-22C String Trimmer Designation of PartsFor machine with Loop handle Assembly of Engine and ShaftMounting of Handle Mounting of Protector Mounting of Nylon Cutter Head FUELS/REFUELING Handling fuelFuel and oil mixture Check points before operationCorrect Handling of Machine Putting Into OperationIdle Adjustment Nylon Cutting HeadStarting the warm engine Checking the Idling speedPage Servicing Instructions Daily checkup and maintenanceCleaning of air cleaner Cleaning of muffler exhaust port Checking the spark plugSupply of grease to gear case Suction head in the fuel tankStorage Maintenance scheduleFault location Emisson Compliance Period Obtaining Warranty Service HOW to Make a Claim Symboles FrançaisConsignes DE Sécurité Instructions généralesUtilisation spéciale de la machine Équipement personnel de protectionRavitaillement MètresInstructions de maintenance Méthode d’utilisationTête de coupe à fill Premier secourCaracteristiques Techniques MS-22CMS-22C Taille-bordures Nomenclature DES PiècesAssemblage DU Mouteur ET DE L’ARBRE Montage DE LA PoignéeMontage DU Dispositif DE Protection Montage DE LA Tête DE Coupe À FIL CARBURANTS/RAVITAILLEMENT Stockage du carburantManipulation Correcte DE LA Machine Mise EN MarcheRéglage DU Ralenti Tête DE Coupe À FIL EN NylonRemplacement du fil en nylon Nettoyage du filtre à air Contrôle et opérations de maintenance réguliersInstructions Relatives AUX Réparations Contôle de la bougie d’allumage Graissage du carter d’engrenageTête d’aspiration dans le réservoir de carburant Nettoyage de l’orifice du pot d’échappementLocalisation des défauts Plan de maintenanceRemisage Símbolos SpanishInstrucciones DE Seguridad Instrucciones generalesMetros Método de trabajo Herramientas de CorteInstrucciones de mantenimiento Primeros AuxiliosEspecificación Modelo MS-22CMS-22C Cortabordes Denominación DE PartesPara maquinas con manubrio en bucle Montaje DE Motor Y EJEMontaje DEL Manillar Montaje DEL Protector Montaje DE LA Cabezal DE Corte DE Nylon COMBUSTIBLES/REABASTECIMIENTO USO Correcto DE LA Máquina Puesta EN MarchaCabezal DE Nylon Precauciones durante la operaciónArranque del motor en caliente Comprobar la velocidad en vacioSustitución de la cuerda de nylon Limpieza del filtro de aire Instrucciones DE ServicioComprobación y mantenimiento diarios Comprobación de la Bujía Suministro de grasa a la caja de engranajesCabezal de succión en el tanque de combustible Limpieza del orificio de salida del silenciadorLocalizacion de averias AlmacenamientoEsquema de mantenimiento Dolmar GmbH Postfach 70 04 Hamburg Germany 6199521201