DeWalt N000589 Chemicals and Cleaning Solvents, Starting, Changing Nozzles on Spray Wand

Page 11

*Caution: The high-pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of spray.

Changing Nozzles on Spray Wand

Danger: Risk of fluid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur.

warning: Flying objects could cause risk of serious injury. Do Not attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles.

1.Pull quick-connect coupler back and insert nozzle.

2. Release quick-connect coupler and twist nozzle to make sure it is secure in coupler.

Warning: Flying object could cause risk of serious injury. Ensure nozzle is completely inserted in quick-connect socket and quick- connect snap ring is fully engaged (forward) before squeezing gun trigger.

Chemicals and Cleaning Solvents

Applying chemicals or cleaning solvents is a low-pressure operation.

NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach.

To apply chemicals and solvents

1.

Press chemical hose (T) onto barbed

 

 

fitting located near high pressure hose

T

 

connection of pump as shown.

 

 

2.

Place the other end of chemical hose

 

 

with filter on it into the container holding

 

 

chemical/cleaning solution.

 

 

NOTE: For every 7 gallons (26.5 liters)

 

of water pumped 1 gallon (3.8 liters) of chemical/cleaning solution will be used.

3.Install low-pressure (black) nozzle into quick connect fitting of spray wand, refer Spray Wand Nozzles. NOTE: Chemicals and soaps will not siphon if the black soap nozzle is not installed on the spray wand.

4.After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty.

Starting

Warning: To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before starting pressure washer.

DANGER: Risk of fluid injection and laceration. When using the high- pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury will occur.

Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fit- tings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

English

11

Image 11
Contents DPH3800 PSI Average Engine Pump SpecificationsSpecifications Model Weight Height WidthDeWALT Definitions Safety GuidelinesImportant Safety Instructions What can happen How to prevent it What can happen Never leave wand unattended while unit is running When Transporting or storing Before each use and while To these very rapidly. AdjustUse a tire pressure gauge To check the tires pressureTo prevent pinching InstallationPressure Washer Assembly Fig For Future USESpray Wand Nozzles Fig Pressure AdjustmentsOperation To apply chemicals and solvents Chemicals and Cleaning SolventsStarting Changing Nozzles on Spray WandTo do so could cause damage to the pump Start-up ProcedureRefer to Chemicals and Cleaning Solvents Turn the water source onTo Check Oil MaintenanceHow To Change Pump Oil Engine PumpEngine To Clean the Water Inlet FilterTo Remove Tires STORAGEDate and Place of Purchase Accessories Service InformationPressure Washer RepairsLimited Warranty Gallons per minute Troubleshooting GuideProblem Code GlossaryCode Possible cause Troubleshooting CodesPossible Solution Troubleshooting Codes Pompe haute pression Huile Utiliser du DP70 Volume d’huile 319,4 ml 10,8 oncesMoteur Caractéristiques techniques de la pompeDirectives de sécurité importantes Fiche techniqueDéfinitions lignes directrices en Matière de sécurité Laisser environ 127 mm Conserver CES DirectivesCe qui peut se produire Comment l’éviter ’incendie Du matériel déposé contreDe l’équipement et pro Voquer une surchauffe etSuite Français Au bras Suivre la procédure deDémarrage correcte pour Qui provoquerait ainsi uneCe qui peut se produire Avertissement Risque d’éclatementConserver CES Directives Pour UN Usage Ultérieur Assemblage de la laveuse haute pression FigRetirer du sac FonctionnementRéglages de la pression Buses du tube de pulvérisation FigApplication DE Produits Chimiques ET Solvants Produits chimiques et solvants de nettoyageChangement DES Buses SUR LE Tube DE Pulvérisation NE PAS cesser la pulvérisation d’eau pour DémarrageLa détente Y lorsque le pistolet n’est pas utilisé Procédure DE DémarrageEnfoncer la détente du pistolet pour activer le jet d’eau Relâcher la détente pour arrêter le jet d’eauMéthode DE Vidange DE ’HUILE DE LA Pompe EntretienPompe Vérification DU Niveau D’HUILENettoyage du filtre de l’admission d’eau RangementLaveuse haute pression AccessoiresDate et lieu de l’achat Information SUR LES RéparationsRéparations Garantie limitéeGlossaire Problème Code Solution ProbableGuide de dépannage Codes de dépannageCodes de dépannage suite Français CAT 67DX MotorEspecificaciones de la bomba Ensamblado del panel Soporte para la boquillaInstrucciones de seguridad importantes EspecificacionesDefiniciones Normas de seguridad ¿Qué puede suceder? Cómo evitarlo Conserve Estas InstruccionesPeligro Riesgo de explosión o incendio Peligro Riesgo Respiratorio asfixia Continuar Laceración ContinuarDE Líquido y laceración Peligro Riesgo de operación insegura ¿Qué puede suceder? Advertencia Riesgo DE superficies calientes Advertencia Riesgo de de estallidoAtención Riesgo de lesión personal. Evite Advertencia Riesgo de quemadura químicaAdvertencia Riesgo DE descarga eléctrica El lugar OperaciónAjustes a la presión Boquillas para la varilla pulverizadora FigInsertada en el adaptador de conexión rápida Productos químicos y solventes de limpiezaCambio DE LAS Boquillas DE LA Varilla Pulverizadora Para Aplicar Productos Químicos Y Solventes Puesta en marchaAbra la fuente de agua Procedimiento DE Puesta EN MarchaLimpieza, consulte la sección Productos Químicos y solventes de limpiezaPara Controlar EL Aceite ApagadoBomba MantenimientoAlmacenamiento Para limpiar el filtro de entrada de aguaLimpieza de las boquillas Para quitar los neumáticosAccesorios Lavadora a presiónGarantía limitada Información DE MantenimientoReparaciones Póliza de GarantíaEspañol Para Otras Localidades GlosarioCódigo Causa posible Guía de detección de problemasCódigos de detección de problemas Problema CódigoCódigos de detección de problemas continuar Español Español Copyright 2007, 2008 D eWALT OCT08 Part No. N000589 r2