Black & Decker TL10 Assembly Instructions, Unpacking Figure B, MID Handle Assembly Figure C

Page 6

ASSEMBLY INSTRUCTIONS

UNPACKING - (FIGURE B)

Remove the frame / upper handle assembly, mid handle, ballast tank, wheels, drag bar, tines and hardware bag from the carton.

The hardware bag contains:

1.Long Carriage Bolts (2)

2.Short Carriage Bolts (4)

3.Flanged Hex Nuts (4)

4.Knobs (2)

5.Wheel Machine Bolts (2)

6.Wheel Washers (4)

7.Steel Pin (1)

8.Long Hairpin Cotter Pin (2)

9.Short Hairpin Cotter Pin (1)

B

ASSEMBLY

DANGER: To prevent serious personal injury, do not connect electric extension cord to unit until fully completing assembly.

Tools required for assembly:

Adjustable or 10 mm wrench

MID HANDLE ASSEMBLY - (FIGURE C)

Ensure that the cord is not pinched and is routed on the top side of the handles.

1.Align the holes in the mid handle with holes in the frame and insert the short carriage bolts (C-1)through the holes.

2.Place a nut (C-2)on each bolt and tighten securely with a 10 mm or adjustable wrench.

UPPER HANDLE ASSEMBLY - (FIGURE D)

Ensure that the cord is not pinched and is routed on the top side of the handles.

1.Align the holes in the upper handle with holes in the mid handle and insert the long carriage bolts (D-1)through the holes.

2.Hand tighten plastic knob (D-2)onto carriage bolts.

3.Clip the lower part of the cord into the lower cord clip (D-3)after the handles are fastened together.

C

D

3

6

Image 6

Contents Catalog Number TL10 VEA EL Español EN LA ContraportadaTable of Contents Safety Guidelines DefinitionsImportant Safety Instructions For ALL DOUBLE-INSULATED AppliancesSafety Warnings and Instructions Double Insulation For ALL AppliancesDonʼt Use in Rain Functional Description MID Handle Assembly Figure C Assembly InstructionsAssembly Upper Handle Assembly Figure DWheel Assembly Figure E Tine Assembly Figure FDrag BAR Assembly Figure G Ballast Tank Figure H ON-OFF Switch Figure JOperating Instructions Attaching Extension Cord to Tiller FigureAdjusting the Drag BAR Figure K Using the TillerCircuit Breaker Transporting and Storage Accessories Problem RecommendationMaintenance Service InformationFull TWO-YEAR Home USE Warranty Mode D?EMPLOI Table DES Matières Lignes Directrices EN Matière DE Sécurité DéfinitionsPréparation Consignes DE Sécurité ImportantesFormation FonctionnementAvertissements DE Sécurité ET Directives Double Isolation Pour Tous LES Appareils ÉlectriquesNe pas utiliser dʼappareil électrique sous la pluie Page Description Fonctionnelle Montage Directives DE MontageDésemballage Figure B Montage DE LA Poignée Centrale Figure CMontage DES Roues Figure E Montage DES Dents Figure FMontage DE LA Barre DE Recouvrement Figure G Réservoir DE Lest Figure H Raccordement DE LA Rallonge AU Rotoculteur FigureInterrupteur DE MARCHE/ARRÊT Figure J Utilisation DU Rotoculteur Réglage DE LA Barre DE Recouvrement Figure KRéglage DE LA Hauteur DES Roues Figure L DisjoncteurProblème Recommandation Débloquage DES DentsTransport ET Entreposage Voir la rubrique Outils électriques Manual DE Instrucciones Índice Pautas DE SEGURIDAD/DEFINICIONESPreparación Instrucciones DE Seguridad ImportantesCapacitación OperaciónAdvertencias E Instrucciones DE Seguridad Doble Aislamiento Para Todos LOS AparatosNo utilizar bajo la lluvia Page Descripción DE LAS Funciones Ensamblaje Instrucciones DE EnsamblajeDesembalaje Figura B Ensamblaje DEL Mango Intermedio Figura CEnsamblaje DE LAS Ruedas Figura E Ensamblaje DE LOS Dientes Figura FInstalación DEL Cable Prolongador EN LA Motoazada Figura Instrucciones DE OperaciónTanque DEL Lastre Figura H Interruptor DE ENCENDIDO/APAGADO Figura JUSO DE LA Motoazada Ajuste DE LA Barra DE Arrastre Figura KAjuste DE LA Posición DE Altura DE LAS Ruedas Figura L DisyuntorMantenimiento Problema RecomendaciónDesatascamiento DE LOS Dientes Transporte Y AlmacenamientoSolamente Para Propositos DE Mexico Años DE Garantia Esta Garantia no Aplica Cuando