Konica Minolta 752 Plug the power cable completely, Do not operate the switches with wet hands

Page 10

Safety Caution

"Cautions on use

Never open or close any covers other than the speciﬁed in this Operation

Manual.

High voltage may be applied on some sections in the device. If you touch them acciden- tally, you may suffer burns or an electric shock.

When replacing FILTER or removing ﬁlm jams in the discharge section, follow the procedure in this Operation Manual;

otherwise, a ﬁre may be caused.

When touching the LCD (glass) on the control panel, do not give a strong mechanical impact; otherwise it may be damaged. If the LCD is damaged, immediately contact a service person.

This cause a breakdown or injuries.

Plug the power cable completely.

If dust is accumulated on the power plug, or the power cable is not plugged properly, this may cause an electric shock or a ﬁre.

Be sure to use the power cable supplied with this device. Do not use an extension cord or do not connect another device to the same wall outlet;

otherwise, a ﬁre or heating may be caused.

Be careful not to trip over the power cable to damage it.

If you continue using the damaged power cable, this may cause an electric shock or ﬁre.

Do not block the air intake or the air outlet of this device;

otherwise, a breakdown may be caused.

Do not start up or shut off the device by plugging or unplugging the power cable;

otherwise, an electric shock or breakdown may be caused.

If it is likely that lightning may occur, stop operating the device, and unplug the power cable.

A breakdown may occur depending on the degree of lightning.

Do not use this device for any purpose other than printing image data;

otherwise, a breakdown may be caused.

Do not operate the switches with wet hands;

otherwise, you may suffer an electric shock.

[NOTE] : If the contents of this page are not legible, order a new manual.

viii DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Image 10

Contents Drypro model Blank DRY Laser Imager Drypro Model Imaging environment IntroductionOperation environment Sorter LiS-752 is optional deviceDescriptions of Symbol Mark Symbol mark Descriptions of symbol markDescriptions on Warning Label Descriptions on warning caution labelPage Front Rear Safety Caution Be sure to ground the device wellBe careful not to trip over the power cable to damage it Plug the power cable completelyDo not operate the switches with wet hands When unplugging the power cable, do not pull it Disposal Precaution PrecautionPrecaution on Installation Location Main Body Name of Each ComponentFront View Rear View Sorter LiS-752 option Structure Control Panel How To OperateDescription on screen Start-up Operation Power saving mode When Start Timer is not set to on Shut-down OperationWhen Start Timer is set to on Touch OK to perform Operation OFF proce- dureShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Maintenance Mode Function of Maintenance ModeShut-down maintenance mode Switching Maintenance ModeStart-up maintenance mode Touch MaintenanceHow To Operate Maintenance Mode Setting Start Timer FunctionSetting Date/Time Time SET Re-printing Printed Page Previous Print Touch Previous Print on the maintenance menu screenTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Touch a LUT name you wish to apply for printing DensityTouch Store MIN DensityCalibration Touch Calibration on the maintenance menu screen Calibrating Density CalibrationAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Touch Cover Open on the maintenance menu screen Opening/closing front cover Cover OpenAdjusting control panel Panel Adjust Touch ExitHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Conﬁrming ﬁlm count data Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Weekly ﬁlm count Monthly ﬁlm countSetting ﬁlm count preference Touch Film Data Setup on the ﬁlm count data screenSetting print preference Touch Print Condition on the maintenance menu screenPrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select After the settings are complete, touch Exit Sets the format of date to be printed on the ﬁlmTouch LUT Library Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch the name of the LUT to be appliedCreating user LUT Touch User LUT on the maintenance menu screenTouch Data on the lower part of the screen Touch Edit on the LUT data screen Conﬁrming the LUT curveSetting power saving mode Touch Power Save on the Maintenance Menu screenHow To Operate Maintenance Mode Error Display and Remedy TroubleshootingError Code Description Remedy Error Display and Remedy Resetting Errors When an error cannot be reset Touch Error QueueRe-starting When Sorter Cover is displayed When Cover Open is displayedRemoving Jam Jam in tray Press in the tray until it locksFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Outer cover of the main unit Service and MaintenancePeriodical Maintenance and Inspection Inside of main unitReplacing Filter Before replacing the FILTER, be sure to touch FILOther service and maintenance Service and Maintenance ScheduleServicing by a user Conﬁrming maintenance and maintenance display Speciﬁcations Drypro ModelSorter Option Speciﬁcations Appendix Time zone and code No. tableHandling and Storage of Unexposed Film Handling and Storage of Developed FilmBlank Blank