Konica Minolta 752 operation manual Start-up Operation

Page 18

3-2.Start-up Operation

3-2. Start-up Operation

Follow the procedure below to turn on the power of the equipment.

(1)Turn ON the power of the breaker located at the lower-right of the device.

(2) Press the start switch below the control panel.

CAUTION

Pressing the start switch again turns OFF the power. In this case, press the start switch again.

(3) The startup screen will appear.

Breaker

Start switch

(4)The WARMING UP screen will appear in approx. 2 minutes.

NOTE

•Although printing cannot be made during warming up, the data from the diagnostic devices can be received. The received data will be printed out after the device goes into the READY status.

•Settings on the maintenance can be made during warming up.

•It takes approx. 25 minutes for the device to go to the READY status. Note that it depends on temperature around the device.

6 DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Image 18

Contents Drypro model Blank DRY Laser Imager Drypro Model Imaging environment IntroductionOperation environment Sorter LiS-752 is optional deviceDescriptions of Symbol Mark Symbol mark Descriptions of symbol markDescriptions on Warning Label Descriptions on warning caution labelPage Front Rear Safety Caution Be sure to ground the device wellPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode When Start Timer is not set to on Shut-down OperationWhen Start Timer is set to on Touch OK to perform Operation OFF proce- dureShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Maintenance Mode Function of Maintenance ModeShut-down maintenance mode Switching Maintenance ModeStart-up maintenance mode Touch MaintenanceHow To Operate Maintenance Mode Setting Start Timer FunctionSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Touch a LUT name you wish to apply for printing DensityTouch Store MIN DensityCalibration Touch Calibration on the maintenance menu screen Calibrating Density CalibrationAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Touch Cover Open on the maintenance menu screen Opening/closing front cover Cover OpenAdjusting control panel Panel Adjust Touch ExitHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Conﬁrming ﬁlm count data Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Weekly ﬁlm count Monthly ﬁlm countSetting ﬁlm count preference Touch Film Data Setup on the ﬁlm count data screenSetting print preference Touch Print Condition on the maintenance menu screenPrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select After the settings are complete, touch Exit Sets the format of date to be printed on the ﬁlmTouch LUT Library Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch the name of the LUT to be appliedTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Touch Edit on the LUT data screen Conﬁrming the LUT curveSetting power saving mode Touch Power Save on the Maintenance Menu screenHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors When an error cannot be reset Touch Error QueueRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Jam in tray Press in the tray until it locksFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Outer cover of the main unit Service and MaintenancePeriodical Maintenance and Inspection Inside of main unitReplacing Filter Before replacing the FILTER, be sure to touch FILService and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display Speciﬁcations Drypro ModelSorter Option Speciﬁcations Appendix Time zone and code No. tableHandling and Storage of Unexposed Film Handling and Storage of Developed FilmBlank Blank