Konica Minolta 752 operation manual Specifications, Drypro Model

Page 81

7. Specifications

Model Name

:

DRYPRO MODEL 752

Model Type

:

Dry Laser Imager

Laser Source

:

Semiconductor Laser

Film Type

:

Konica Medical Imaging Film SD-P, SD-PC, DR-P

Film Size

:

14" x 17"

 

 

14" x 14"

 

 

11" x 14"

 

 

The film sizes of 14" x 17", 14" x 14", and 11" x 14" are set at installation.

Number of film

:

Actual No. 125 sheets, 127 sheets in package

 

 

Of two sheets of film, one for calibration and one for dummy film

Interface (IN)

:

Ethernet 10base- T/100base- TX

Protocol

:

DICOM Print Management

Ports (IN)

:

16 ports max.

Main Memory

:

128MB (standard)

Image Memory

:

Hard Disk . . . . . . . . . . . 20GB (standard)

 

 

Print Memory . . . . . . . . 256MB (standard)

Performance

:

120 sheets/H (Continuous process of 14" x 17"-film)

Dimensions (W x D x H)

:

750 x 690 x 1410 mm (29.5" x 27.2" x 55.5") without Sorter option

Weight

:

Approx. 280kg (616.7 lb) DP752 Approx. 250Kg (551lb) DP751

Power

:

100 V - 120 V ± 10% AC (single-phase) / 220 V - 240 V ± 10% AC (single-

 

 

phase), 9.0 A - 7.5 A / 4.5 A - 4.0 A (50 / 60Hz)

Heat Generation

:

Approx. 950kJ/H (226kcal/H)

Operating Condition

:

15 to 30 °C (59 to 86 °F) / 30 to 70%RH (No condensation)

Storage and Transport Condition :

-20 to 60 °C (-4 to 140 °F) / 20 to 90%RH (No condensation)

Noise Level

:

55dB or less

Control Panel

:

LCD with a touch panel

Film Supply

:

Tray

Number of Trays

:

2 trays

Image Data Input

:

8 bits (256 steps) or 12 bits (4096 steps) (depending on the image signal of the

 

 

modality)

Output Gradation

:

16384 levels (14 bits)

Image Mode

:

Pixel replication / Function interpolation

Pixel Size

:

Optical scan / 40 to 80 µm, Variable, Subscan / 40 µm fixed

 

:

(The recorded pixel size depends on the number of pixels and the format in the

 

 

diagnostic device.)

Image Matrix

:

When connected to the Regius

When connected to any other than

the Regius

 

 

 

8,850 x 10,650 pixels (14" x 17")

8,550 x 10,225 pixels

 

 

8,850 x 8,750 pixels (14" x 14")

8,550 x 8,325 pixels

 

 

6,875 x 8,850 pixels (11" x 14")

6,675 x 8,325 pixels

 

 

Image Format

: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 25, 30, 35, 36, 42, 48, 54, 56, 60, 63, 64

Positive/Negative

:

Available

Trim

:

Available

DRYPRO MODEL 752 Operation Manual USA Ver.0.12 2003.5 69

Page 80 Page 82
Image 81
Page 80 Page 82
Contents Drypro model Blank DRY Laser Imager Drypro Model Operation environment IntroductionImaging environment Sorter LiS-752 is optional deviceSymbol mark Descriptions of symbol mark Descriptions of Symbol MarkDescriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety CautionPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to onTouch OK to perform Operation OFF proce- dure When Start Timer is set to onShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance ModeStart-up maintenance mode Switching Maintenance ModeShut-down maintenance mode Touch MaintenanceSetting Start Timer Function How To Operate Maintenance ModeSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printingMIN Density Touch StoreCalibrating Density Calibration Calibration Touch Calibration on the maintenance menu screenAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screenTouch Exit Adjusting control panel Panel AdjustHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the confirm message Cold Start Touch Film Data on the maintenance menu screen Confirming and setting film count dataConfirming film count data Weekly film count Monthly film countTouch Film Data Setup on the film count data screen Setting film count preferenceTouch Print Condition on the maintenance menu screen Setting print preferencePrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the film After the settings are complete, touch ExitTouch the user LUT name to be set on the LUT select screen Setting user LUTTouch LUT Library Touch the name of the LUT to be appliedTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Confirming the LUT curve Touch Edit on the LUT data screenTouch Power Save on the Maintenance Menu screen Setting power saving modeHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be resetRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Press in the tray until it locks Jam in trayFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Periodical Maintenance and Inspection Service and MaintenanceOuter cover of the main unit Inside of main unitBefore replacing the FILTER, be sure to touch FIL Replacing FilterService and Maintenance Schedule Other service and maintenanceServicing by a user Confirming maintenance and maintenance display Drypro Model SpecificationsSorter Option Specifications Time zone and code No. table AppendixHandling and Storage of Developed Film Handling and Storage of Unexposed FilmBlank Blank
Top Page Image Contents