Konica Minolta 752 operation manual Film outlet cover

Page 66

5-3.Removing Jam

"Film jam between decent transport section and exposure section

The screen on the right shows the example where a film jam occurs between the decent transport section and the exposure section (the subscan unit). Follow the procedure below to remove the jammed film.

(1)Lift the film outlet cover on the front-lower part of the device to open by lifting the green handle.

Opening the cover to an upright position fixes it with magnets.

(2)Turn the green handle located on the front-left until the leading edge of film can be seen in the film out- let.

The film in the descent transport section is transported to the position control section.

(3)While turning the handle clockwise, put your hand from the film outlet and fold the edge of the film back.

(4)When the trailing edge of the film removes from the transport roller, take out the film from the film outlet.

(5)Close the film outlet cover and then the front cover.

The normal screen will re-appear after a while when the mes- sage of "PLEASE WAIT" appears.

When there queued print data remains, printing starts automat- ically.

CAUTION

The front cover cannot be closed with the film outlet cover open. If you find it difficult to close the front cover, check that the film outlet cover is closed.

Do not close the front cover forcibly.

Film outlet cover

Green edge

Green handle

Film

54 DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Drypro model Blank DRY Laser Imager Drypro Model Imaging environment IntroductionOperation environment Sorter LiS-752 is optional deviceDescriptions of Symbol Mark Symbol mark Descriptions of symbol markDescriptions on Warning Label Descriptions on warning caution labelPage Front Rear Safety Caution Be sure to ground the device wellPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode When Start Timer is not set to on Shut-down OperationWhen Start Timer is set to on Touch OK to perform Operation OFF proce- dureShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Maintenance Mode Function of Maintenance ModeShut-down maintenance mode Switching Maintenance ModeStart-up maintenance mode Touch MaintenanceHow To Operate Maintenance Mode Setting Start Timer FunctionSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Touch a LUT name you wish to apply for printing DensityTouch Store MIN DensityCalibration Touch Calibration on the maintenance menu screen Calibrating Density CalibrationAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Touch Cover Open on the maintenance menu screen Opening/closing front cover Cover OpenAdjusting control panel Panel Adjust Touch ExitHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the confirm message Cold Start Confirming film count data Confirming and setting film count dataTouch Film Data on the maintenance menu screen Weekly film count Monthly film countSetting film count preference Touch Film Data Setup on the film count data screenSetting print preference Touch Print Condition on the maintenance menu screenPrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select After the settings are complete, touch Exit Sets the format of date to be printed on the filmTouch LUT Library Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch the name of the LUT to be appliedTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Touch Edit on the LUT data screen Confirming the LUT curveSetting power saving mode Touch Power Save on the Maintenance Menu screenHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors When an error cannot be reset Touch Error QueueRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Jam in tray Press in the tray until it locksFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Outer cover of the main unit Service and MaintenancePeriodical Maintenance and Inspection Inside of main unitReplacing Filter Before replacing the FILTER, be sure to touch FILService and Maintenance Schedule Other service and maintenanceServicing by a user Confirming maintenance and maintenance display Specifications Drypro ModelSorter Option Specifications Appendix Time zone and code No. tableHandling and Storage of Unexposed Film Handling and Storage of Developed FilmBlank Blank
Top Page Image Contents