Konica Minolta 752 operation manual Structure

Page 16

2. Structure

(7)

(10)

(1)

(2)

(11)

(3)

- Sorter LiS-752 is optional device.

(8)

(6)

(5)

(4)

(9)

(1)Supply section

Picks up each sheet of ﬁlm from the tray unit, and sends to the descent transport section.

(2)Descent transport section

Sends the picked-up ﬁlm in the supply section to the position control section.

(6)HPRO (Heat Processing) section

Processes the exposed ﬁlm by heating.

(7)Cooling/Discharge section

Cools the heat-processed ﬁlm and discharges it.

(8)Air-cooling section

Remove the odor generated by heat-processing with a ﬁlter.

(3)Position control section

Aligns the ﬁlm sent from the descent transport unit hor- izontally, and sends it to the exposure section.

(4)Exposure section (a: Subscan unit, b: Optical unit)

Performs a laser scanning in synchronization with the ﬁlm transport and prints an image on the ﬁlm.

(5)Elevator transport section

Sends the ﬁlm to the HPRO (Heat Processing) section after the exposure.

(9)Electrical control section

Consists of the power supply unit for supplying the power to the device and the control unit for controlling the entire device, communicating with the diagnostic devices, and processing / controlling images.

By installing an optional battery for UPS (uninterruptible power supply), the system in the control unit can be backed up even though power failure occurs due to electrical accidents.

(10)Control panel

Operates and makes settings of the device.

(11)Sorter (option)

Discharges the ﬁlm discharged from the main body into the speciﬁed bin.

4 DRYPRO MODEL 752 Operation Manual Ver.0.12 2002.7

Image 16

Contents Drypro model Blank DRY Laser Imager Drypro Model Introduction Operation environmentImaging environment Sorter LiS-752 is optional deviceDescriptions of Symbol Mark Symbol mark Descriptions of symbol markDescriptions on Warning Label Descriptions on warning caution labelPage Front Rear Safety Caution Be sure to ground the device wellBe careful not to trip over the power cable to damage it Plug the power cable completelyDo not operate the switches with wet hands When unplugging the power cable, do not pull it Disposal Precaution PrecautionPrecaution on Installation Location Main Body Name of Each ComponentFront View Rear View Sorter LiS-752 option Structure Control Panel How To OperateDescription on screen Start-up Operation Power saving mode When Start Timer is not set to on Shut-down OperationWhen Start Timer is set to on Touch OK to perform Operation OFF proce- dureShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Maintenance Mode Function of Maintenance ModeSwitching Maintenance Mode Start-up maintenance modeShut-down maintenance mode Touch MaintenanceHow To Operate Maintenance Mode Setting Start Timer FunctionSetting Date/Time Time SET Re-printing Printed Page Previous Print Touch Previous Print on the maintenance menu screenTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Touch a LUT name you wish to apply for printing DensityTouch Store MIN DensityCalibration Touch Calibration on the maintenance menu screen Calibrating Density CalibrationAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Touch Cover Open on the maintenance menu screen Opening/closing front cover Cover OpenAdjusting control panel Panel Adjust Touch ExitHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Conﬁrming and setting ﬁlm count data Touch Film Data on the maintenance menu screenConﬁrming ﬁlm count data Weekly ﬁlm count Monthly ﬁlm countSetting ﬁlm count preference Touch Film Data Setup on the ﬁlm count data screenSetting print preference Touch Print Condition on the maintenance menu screenPrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select After the settings are complete, touch Exit Sets the format of date to be printed on the ﬁlmSetting user LUT Touch the user LUT name to be set on the LUT select screenTouch LUT Library Touch the name of the LUT to be appliedCreating user LUT Touch User LUT on the maintenance menu screenTouch Data on the lower part of the screen Touch Edit on the LUT data screen Conﬁrming the LUT curveSetting power saving mode Touch Power Save on the Maintenance Menu screenHow To Operate Maintenance Mode Error Display and Remedy TroubleshootingError Code Description Remedy Error Display and Remedy Resetting Errors When an error cannot be reset Touch Error QueueRe-starting When Sorter Cover is displayed When Cover Open is displayedRemoving Jam Jam in tray Press in the tray until it locksFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Service and Maintenance Periodical Maintenance and InspectionOuter cover of the main unit Inside of main unitReplacing Filter Before replacing the FILTER, be sure to touch FILOther service and maintenance Service and Maintenance ScheduleServicing by a user Conﬁrming maintenance and maintenance display Speciﬁcations Drypro ModelSorter Option Speciﬁcations Appendix Time zone and code No. tableHandling and Storage of Unexposed Film Handling and Storage of Developed FilmBlank Blank