Konica Minolta 752 operation manual DRY Laser Imager Drypro Model

Page 3

DRY LASER IMAGER DRYPRO MODEL 752

Table of Contents

Introduction			ii
Descriptions of Symbol Mark			iii
Descriptions on Warning Label			iv
Warning Label			v
Warning Label Location			vi
Safety Caution			vii
Precaution			x
1.	Name of Each Component		1
	1-1.	Main Body	1
	1-2.	Sorter LiS-752 (option)	3
2.	Structure		4
3.	How To Operate		5
	3-1.	Control Panel	5
	3-2.	Start-up Operation	6
	3-3.	Shut-down Operation	8
	3-4.	Film Loading	11
4.	Maintenance Mode		16
	4-1. Function of Maintenance Mode		16
	4-2.	Switching Maintenance Mode	17
	4-3. How To Operate Maintenance Mode		18
5.	Troubleshooting		47
	5-1. Error Display and Remedy		47
	5-2.	Resetting Errors	49
	5-3.	Removing Jam	52
	5-4. When Film Fails to be Loaded		61
6.	Service and Maintenance		65
	6-1. Periodical Maintenance and Inspection		65
	6-2.	Replacing FILTER	66
	6-3. Service and Maintenance Schedule		67
7.	Speciﬁcations		69
Appendix			71
HANDLING AND STORAGE OF DRY FILM			72

This device uses laser. Direct exposure of the laser on the skin or in the eyes may lead to serious injuries. And, high voltage may be applied on some sections in the device. Be careful not to suffer an electrical shock upon handling the device.

Be sure to observe the following in order to prevent any danger.

1.NEVER remove the external and internal covers with a screwdriver, and others.

2.NEVER perform any operations, adjustments, or actions other than the speciﬁed in this Operation Manual; otherwise, you may be exposed to dangerous radiation.

3.If any problem occurs in this device, contact a service person. NEVER use the troubled device as it is dangerous.

DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6 i

Image 3

Contents Drypro model Blank DRY Laser Imager Drypro Model Sorter LiS-752 is optional device IntroductionOperation environment Imaging environmentSymbol mark Descriptions of symbol mark Descriptions of Symbol MarkDescriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety CautionPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to onTouch OK to perform Operation OFF proce- dure When Start Timer is set to onShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance ModeTouch Maintenance Switching Maintenance ModeStart-up maintenance mode Shut-down maintenance modeSetting Start Timer Function How To Operate Maintenance ModeSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printingMIN Density Touch StoreCalibrating Density Calibration Calibration Touch Calibration on the maintenance menu screenAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screenTouch Exit Adjusting control panel Panel AdjustHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Weekly ﬁlm count Monthly ﬁlm count Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Conﬁrming ﬁlm count dataTouch Film Data Setup on the ﬁlm count data screen Setting ﬁlm count preferenceTouch Print Condition on the maintenance menu screen Setting print preferencePrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the ﬁlm After the settings are complete, touch ExitTouch the name of the LUT to be applied Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch LUT LibraryTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Conﬁrming the LUT curve Touch Edit on the LUT data screenTouch Power Save on the Maintenance Menu screen Setting power saving modeHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be resetRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Press in the tray until it locks Jam in trayFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Inside of main unit Service and MaintenancePeriodical Maintenance and Inspection Outer cover of the main unitBefore replacing the FILTER, be sure to touch FIL Replacing FilterService and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display Drypro Model SpeciﬁcationsSorter Option Speciﬁcations Time zone and code No. table AppendixHandling and Storage of Developed Film Handling and Storage of Unexposed FilmBlank Blank