Konica Minolta 752 operation manual Power saving mode

Page 19

3-2.Start-up Operation

(5)When READY appears on the message column, printing can be made.

NOTE

Use the START TIMER function to set the device to READY on the speciﬁed time without pressing the start switch.

(Refer to page 18 for details on how to set the START TIMER function.)

"Power saving mode

The DRYPRO has the power saving mode that saves power consumption automatically after no data is printed or no printing data is received for a speciﬁed time.

When the DRYPRO goes into the power saving mode, the screen on the right appears on the control panel, and the backlight fades out. The power saving mode is not enabled during OFF LINE mode.

The DRYPRO exits from the power saving mode and starts warming up by performing the following opera- tions.

•Touch [WAKE UP] on the control panel.

•When the DRYPRO receives printing data from a diagnostic device, it exits from the power saving mode automatically, and starts printing when it goes into the READY status.

NOTE

•The time period over which the DRYPRO goes into the READY status depends on the power saving mode levels.

•You can set Use/Disuse or the level of the power saving mode on the MAINTENANCE MENU screen. (Refer to page 45.)

DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6 7

Image 19

Contents Drypro model Blank DRY Laser Imager Drypro Model Sorter LiS-752 is optional device IntroductionOperation environment Imaging environmentSymbol mark Descriptions of symbol mark Descriptions of Symbol MarkDescriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety CautionBe careful not to trip over the power cable to damage it Plug the power cable completelyDo not operate the switches with wet hands When unplugging the power cable, do not pull it Disposal Precaution PrecautionPrecaution on Installation Location Main Body Name of Each ComponentFront View Rear View Sorter LiS-752 option Structure Control Panel How To OperateDescription on screen Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to onTouch OK to perform Operation OFF proce- dure When Start Timer is set to onShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance ModeTouch Maintenance Switching Maintenance ModeStart-up maintenance mode Shut-down maintenance modeSetting Start Timer Function How To Operate Maintenance ModeSetting Date/Time Time SET Re-printing Printed Page Previous Print Touch Previous Print on the maintenance menu screenTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printingMIN Density Touch StoreCalibrating Density Calibration Calibration Touch Calibration on the maintenance menu screenAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screenTouch Exit Adjusting control panel Panel AdjustHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Weekly ﬁlm count Monthly ﬁlm count Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Conﬁrming ﬁlm count dataTouch Film Data Setup on the ﬁlm count data screen Setting ﬁlm count preferenceTouch Print Condition on the maintenance menu screen Setting print preferencePrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the ﬁlm After the settings are complete, touch ExitTouch the name of the LUT to be applied Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch LUT LibraryCreating user LUT Touch User LUT on the maintenance menu screenTouch Data on the lower part of the screen Conﬁrming the LUT curve Touch Edit on the LUT data screenTouch Power Save on the Maintenance Menu screen Setting power saving modeHow To Operate Maintenance Mode Error Display and Remedy TroubleshootingError Code Description Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be resetRe-starting When Sorter Cover is displayed When Cover Open is displayedRemoving Jam Press in the tray until it locks Jam in trayFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Inside of main unit Service and MaintenancePeriodical Maintenance and Inspection Outer cover of the main unitBefore replacing the FILTER, be sure to touch FIL Replacing FilterOther service and maintenance Service and Maintenance ScheduleServicing by a user Conﬁrming maintenance and maintenance display Drypro Model SpeciﬁcationsSorter Option Speciﬁcations Time zone and code No. table AppendixHandling and Storage of Developed Film Handling and Storage of Unexposed FilmBlank Blank