Konica Minolta 752 operation manual Cutouts

Page 72

5-3.Removing Jam

(6)Put the ﬁlm transport guide back, and remove the sorter left cover.

CAUTION

When you put the ﬁlm transport guide back to the original position, lift the ﬁlm transport guide (lower) once, and hook the cutout at both ends of the lower guide board on the guide pins as shown in the ﬁgure on the right.

Film transport guide

(lower)

Guide pins

Cutouts

60 DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Image 72

Contents Drypro model Blank DRY Laser Imager Drypro Model Introduction Operation environmentImaging environment Sorter LiS-752 is optional deviceDescriptions of Symbol Mark Symbol mark Descriptions of symbol markDescriptions on Warning Label Descriptions on warning caution labelPage Front Rear Safety Caution Be sure to ground the device wellPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode When Start Timer is not set to on Shut-down OperationWhen Start Timer is set to on Touch OK to perform Operation OFF proce- dureShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Maintenance Mode Function of Maintenance ModeSwitching Maintenance Mode Start-up maintenance modeShut-down maintenance mode Touch MaintenanceHow To Operate Maintenance Mode Setting Start Timer FunctionSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Touch a LUT name you wish to apply for printing DensityTouch Store MIN DensityCalibration Touch Calibration on the maintenance menu screen Calibrating Density CalibrationAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Touch Cover Open on the maintenance menu screen Opening/closing front cover Cover OpenAdjusting control panel Panel Adjust Touch ExitHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Conﬁrming and setting ﬁlm count data Touch Film Data on the maintenance menu screenConﬁrming ﬁlm count data Weekly ﬁlm count Monthly ﬁlm countSetting ﬁlm count preference Touch Film Data Setup on the ﬁlm count data screenSetting print preference Touch Print Condition on the maintenance menu screenPrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select After the settings are complete, touch Exit Sets the format of date to be printed on the ﬁlmSetting user LUT Touch the user LUT name to be set on the LUT select screenTouch LUT Library Touch the name of the LUT to be appliedTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Touch Edit on the LUT data screen Conﬁrming the LUT curveSetting power saving mode Touch Power Save on the Maintenance Menu screenHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors When an error cannot be reset Touch Error QueueRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Jam in tray Press in the tray until it locksFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Service and Maintenance Periodical Maintenance and InspectionOuter cover of the main unit Inside of main unitReplacing Filter Before replacing the FILTER, be sure to touch FILService and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display Speciﬁcations Drypro ModelSorter Option Speciﬁcations Appendix Time zone and code No. tableHandling and Storage of Unexposed Film Handling and Storage of Developed FilmBlank Blank