Konica Minolta 752 Troubleshooting, Error Display and Remedy, Error Code Description Remedy

Page 59

5. Troubleshooting

5-1. Error Display and Remedy

When an error occurs in the device, the error code and the description are displayed on the message column on the control panel.

The following shows the errors and the remedies displayed in this device.

Error Code	Description	Remedy

E4A20	The front cover is open.	Close the front cover.
E4A21

E4110	The ﬁlm cannot be sent from the upper	• Pull out the upper tray, and remove jammed ﬁlm. (Refer to
E4112	tray.	page 53.)
		• When a ﬁlm jam occurs when loading the ﬁlm, load the
		ﬁlm again. (Refer to page 61.)

E4126	The upper tray is open.	Close the upper tray.

E4210	The ﬁlm cannot be sent from the lower	• Pull out the lower tray, and remove ﬁlm jam. (Refer to page
E4212	tray.	53.)
		• When a ﬁlm jam occurs when loading the ﬁlm, load the
		ﬁlm again. (Refer to page 61.)

E4226	The lower tray is open.	Close the lower tray.

E4111	The ﬁlm cannot be sent from the descent	Open the front cover, and remove a jammed ﬁlm. (Refer to
E4113	transport section.	page 54.)
E4211	Film jams occur between the descent
E4213	transport section and the exposure sec-
E4310	tion.
E4310
E4311
E4312
E4410
E4411

E4510	The ﬁlm cannot be sent from the elevator	Open the front cover, and remove a jammed ﬁlm. (Refer to
	transport section.	page 55.)
	Film jams occur between the exposure
	section and the elevator transport section.

E4511	Film remains in the HPRO (heat process-	Open the front cover, and remove jammed ﬁlm. (Refer to
E4610	ing) section.	page 56.)
E4611	Film jams occur in the HPRO (heat pro-
E4710	cessing) section.

E4120	No FILTER exists.	Place FILTER.
E4220	FILTER cannot be detected.	Place FILTER in the speciﬁed place correctly. (Refer to page
E4A22		66.)

E4810	Film remains in the sorter basket.	Remove the ﬁlm from the inlet of the sorter. (Refer to page
E4811		58.)

E4812	The sorter cover is open.	Close the sorter cover.
E4820

DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6 47

Image 59

Contents Drypro model Blank DRY Laser Imager Drypro Model Sorter LiS-752 is optional device IntroductionOperation environment Imaging environmentSymbol mark Descriptions of symbol mark Descriptions of Symbol MarkDescriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety CautionDo not operate the switches with wet hands Plug the power cable completelyBe careful not to trip over the power cable to damage it When unplugging the power cable, do not pull it Precaution on Installation Location PrecautionDisposal Precaution Front View Name of Each ComponentMain Body Rear View Sorter LiS-752 option Structure Description on screen How To OperateControl Panel Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to onTouch OK to perform Operation OFF proce- dure When Start Timer is set to onShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance ModeTouch Maintenance Switching Maintenance ModeStart-up maintenance mode Shut-down maintenance modeSetting Start Timer Function How To Operate Maintenance ModeSetting Date/Time Time SET Touch on the upper part of the screen Touch Previous Print on the maintenance menu screenRe-printing Printed Page Previous Print Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printingMIN Density Touch StoreCalibrating Density Calibration Calibration Touch Calibration on the maintenance menu screenAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screenTouch Exit Adjusting control panel Panel AdjustHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Weekly ﬁlm count Monthly ﬁlm count Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Conﬁrming ﬁlm count dataTouch Film Data Setup on the ﬁlm count data screen Setting ﬁlm count preferenceTouch Print Condition on the maintenance menu screen Setting print preferencePrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the ﬁlm After the settings are complete, touch ExitTouch the name of the LUT to be applied Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch LUT LibraryTouch Data on the lower part of the screen Touch User LUT on the maintenance menu screenCreating user LUT Conﬁrming the LUT curve Touch Edit on the LUT data screenTouch Power Save on the Maintenance Menu screen Setting power saving modeHow To Operate Maintenance Mode Error Code Description Remedy TroubleshootingError Display and Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be resetRe-starting Removing Jam When Cover Open is displayedWhen Sorter Cover is displayed Press in the tray until it locks Jam in trayFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Inside of main unit Service and MaintenancePeriodical Maintenance and Inspection Outer cover of the main unitBefore replacing the FILTER, be sure to touch FIL Replacing FilterServicing by a user Service and Maintenance ScheduleOther service and maintenance Conﬁrming maintenance and maintenance display Drypro Model SpeciﬁcationsSorter Option Speciﬁcations Time zone and code No. table AppendixHandling and Storage of Developed Film Handling and Storage of Unexposed FilmBlank Blank