Konica Minolta 752 Setting power saving mode, Touch Power Save on the Maintenance Menu screen

Page 57

4-3.How To Operate Maintenance Mode

"Setting power saving mode

The DRYPRO has the power saving mode that saves power consumption automatically after no data is printed for a speciﬁed time.

The power saving mode has two kinds of settings: [TOUCH PANEL POWER SAVE] for let the backlight of the control panel fade out, and [HEAT ROLLER POWER SAVE] for lowering the temperature in the HPRO.

Follow the procedure below to set the power saving mode.

(1)Touch [POWER SAVE] on the MAINTENANCE MENU screen.

The power save set (POWER SAVE) screen will appear.

(2)In order to let the backlight of the control panel fade out, touch [ON] on the right of [TOUCH PANEL POWER SAVE].

(3)Touch the key on the right of [TIMER], then touch the numeric keys on the lower part of the screen to set the time (minute) to go into the power saving mode.

(4)In order to save power consumption in the HPRO section, touch [L], [M], or [H] on the right of [HEAT

ROLLER POWER SAVE].

[L], [M], or [H] shows the temperature in the HPRO section in the power saving mode.[L] means that the temperature is the lowest, and [M] means it is medium, and [H] means it is the highest.

CAUTION

If you set the temperature to low, the power con- sumption can be saved much in the power saving mode. However it takes longer for the DRYPRO to exit from the power saving mode and go into the READY status.

The recovering time period is about 10 minutes when [L] is set, 6 minutes when [M] is set, and 3 minutes when [H] is set.

DRYPRO MODEL 752 Operation Manual Ver.0.12 2002.7 45

Image 57

Contents Drypro model Blank DRY Laser Imager Drypro Model Operation environment IntroductionImaging environment Sorter LiS-752 is optional deviceSymbol mark Descriptions of symbol mark Descriptions of Symbol MarkDescriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety CautionPlug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to onTouch OK to perform Operation OFF proce- dure When Start Timer is set to onShut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance ModeStart-up maintenance mode Switching Maintenance ModeShut-down maintenance mode Touch MaintenanceSetting Start Timer Function How To Operate Maintenance ModeSetting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printingMIN Density Touch StoreCalibrating Density Calibration Calibration Touch Calibration on the maintenance menu screenAutomatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screenTouch Exit Adjusting control panel Panel AdjustHow To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Touch Film Data on the maintenance menu screen Conﬁrming and setting ﬁlm count dataConﬁrming ﬁlm count data Weekly ﬁlm count Monthly ﬁlm countTouch Film Data Setup on the ﬁlm count data screen Setting ﬁlm count preferenceTouch Print Condition on the maintenance menu screen Setting print preferencePrint preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the ﬁlm After the settings are complete, touch ExitTouch the user LUT name to be set on the LUT select screen Setting user LUTTouch LUT Library Touch the name of the LUT to be appliedTouch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Conﬁrming the LUT curve Touch Edit on the LUT data screenTouch Power Save on the Maintenance Menu screen Setting power saving modeHow To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be resetRe-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Press in the tray until it locks Jam in trayFilm outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Periodical Maintenance and Inspection Service and MaintenanceOuter cover of the main unit Inside of main unitBefore replacing the FILTER, be sure to touch FIL Replacing FilterService and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display Drypro Model SpeciﬁcationsSorter Option Speciﬁcations Time zone and code No. table AppendixHandling and Storage of Developed Film Handling and Storage of Unexposed FilmBlank Blank