Xerox PE120i manual Configure Snmp, Properties link

Page 83

SNMP

Use these instructions to configure the Simple Network Management Protocol (SNMP) using CentreWare Internet Services.

Configure SNMP

To configure SNMP, perform these steps:

1

¾ Enable CentreWare Internet Services (see “Enabling Internet Services” on page 6-5).

¾At the CentreWare Internet Services Home Page for the WorkCentre PE120i, select the

2

[Properties] link.

3

¾ Select the plus symbol [+] to the left of the Connectivity folder in the Properties frame,

and then select the [+] symbol to the left of the Protocols folder.

¾Select [SNMP] and check the Protocol Configuration details are correct. If any of the

4

details are incorrect then enter the correct information.

5

¾ Make the following selections and settings in the SNMP Properties section of the frame:

Select the checkbox to enable the SNMP Protocol.

Click the [Edit] button to configure SNMP.

You can change the GET and SET Community Names.

NOTE: Changes made to the GET and SET Community Names will require corresponding changes for each application that uses the protocol.

Network Installation Using Internet Services

You can set the Default TRAP Community Name.

NOTE: This specifies the default trap community name for all traps generated by the machine and can be overridden by the trap community name specified for each TRAP destination address. It may not have the same trap community name as that specified fro another address.

You can Enable Authentication Failure Generic Traps to generate a trap for every SNMP request received by the machine that contains an invalid community name.

¾Click the [Apply] button to implement any changes and return to the first screen.

Xerox WorkCentre PE120i System Administration Guide

Page 6-17

Image 83
Contents WorkCentre PE120i System Administration Guide By Xerox Corporation. All rights reserved Table of Contents Test Print Information Checklist AppleTalk InstallationInformation Checklist Network Tools Information Checklist Installation ProcedureInformation Checklist Fax Setup using Internet Services TestingMaintenance using Internet Services Welcome Xerox WorkCentre PE120i IntroductionDirectly onto any area Aerosol cleaners or pour fluidsAbout This Guide Or strong chemical solvents orRelated Information Sources Customer Support Safety Welcome Safety Standards Regulatory Information FCC Part Reference CFR Section Laser SafetyQuestion Is Xerox equipment safe? What is the Electricity at Work Regulation?Electricity at Work Regulations UK only Require records of all tests Question Is the Xerox equipment in my premises safe?My premises AL7 1HE France IrelandPortugal Finland Italy Spain Regulations EuropeData Coupler Information Regulations USAFax Send Header Requirements Welcome Regulations Canada Energy Star Environmental ComplianceIntroduction Basic Network InstallationInformation Checklist Installation Procedure Basic TCP/IP SettingsBasic Enabling or Disabling TCP/IPAutomatically setting TCP/IP Addresses Network Communication SetupPrinting a System Data Manually setting TCP/IP Addresses Manual IP Address Xxx.xxx.xxx.xxx Workstation Setup Test Print NetWare NetWare NetWare 4.x, 5.x NetWare EnvironmentsIPX Queue Based Printing Installation OptionsNetwork Communication Setup Using NetWare UtilitiesInstallation Procedure Auto Enable Enable Snap Off NetWare Setup Test Print ¾ Information Checklist -2 ¾ Workstation Setup Print Driver Installation for Networked PrintersPrint Driver Installation for Networked Printers Workstation Setup ¾ Select Start, select Printers and Faxes Windows XP TCP/IP¾ Continue with Test Print on Windows 2000 TCP/IP Print Driver Installation for Networked Printers Have Disk Windows NT V4.0 TCP/IPPanel Print Driver Installation for Networked Printers Windows 98/Me Windows XP Internet Printing Protocol Windows 2000 Internet Printing Protocol ¾ Choose the WorkCentre PE120i Apple Mac OSX with RendezvousTest Print AppleTalk AppleTalk AppleTalk Installation Network Setup Config Network Ethertalk Printer Driver Installation Mac OS 8x,9x only Xerox WCPE120i ppd should be displayed. Click the OK button Setting the Printer Driver Mac OS 8x,9x onlyPrinter Driver Installation Mac OSX only ¾ Select Appletalk Setting the Printer Driver Mac OSX onlyTest Print AppleTalk Network Installation Using Internet Services Network Installation Using Internet Services Using CentreWare Internet Services Network Communication Setup Enabling Internet Services Configuring the Network Ethernet AppleTalk Configure the WorkCentre PE120iSelections to take effect Test Print NetWare Pconsole or Nwadmin SetupSet the Queue Poll Interval ¾ Continue with Configure the WorkCentre PE120i¾ Enable the Service Advertising Protocol SAP TCP/IP ¾ Continue with Test Print Test Print Properties link Configure SnmpFrame Ssdp Configure SsdpEnter the Port Number LPR/LPDServices ¾ Select Raw TCP/IP Printing Raw TCP/IP PrintingProperties tab ¾ Open a document on a client workstation IPP Access the WorkCentre PE120i embedded Http Server Home Http Test Print Network Installation Using Internet Services Local Connection Local Connection Installation Procedure Driver Installation 12 ¾ Continue with Workstation Setup ¾ Continue with Workstation Setup 10 ¾ 11 ¾ 12 ¾ ¾ Continue with Workstation Setup Workstation Setup Properties window will be displayed Local Connection Test Scan Test Print or ScanFax Fax Enabling Internet Services Fax Setup using Internet ServicesFax General Setup Fax Phone Book Setup Testing Administration Tools Network Tools Reset NetworkSet To Defaults Maintenance using Internet Services Status tab Checking Printer StatusPrint tab Printing ReportsDefining the Printer Checking Configurations Enter your Admin User Name and Password Making General Maintenance SettingsMaintenance tab Upgrading Firmware Assistance tab Obtaining AssistanceAdministration Tools CSV GlossaryHttp Ieee PCL SPX 5-8 IndexIndex Index-iii
Related manuals
Manual 20 pages 909 b Manual 7 pages 49.77 Kb