Cisco Systems 78-16845-01 appendix Snmp No Data Error

Page 79

Appendix J Troubleshooting

J.10.7 Configuration Center Management

•Dspcd command output from the switch for the controller card and the service module where this error is detected.

•Ddspln or dspport command output, if this error seen for a line or port.

Possible alternative workaround—None.

J.10.7.2.2 SNMP No Data Error

An SNMP NO DATA error is seen while launching the Configuration Center (either by the drag-and-drop method or the right-click method) for a network element.

See if the network element for which this error occurred is active, and that the node is synced up. To do this, use the selnd command on the CTM machine.

Check whether the correct community strings are used. If this error is noticed for a properly synced up node on an active element, perform the following:

Step 1 Use an SNMP Manager tool to determine whether the switch is responding to SNMP queries.

The SNMP MIB objects to be queried for a particular dialog box can be obtained from the /svplus/log/configserver.log file. Refer to the entries in this log file when this error occurs and perform the following:

a.Using HP-OV SNMP operations, perform a walk (on "system" MIB table for this example, using public community string) as /opt/OV/bin/snmpwalk -c public nodeName system.

b.If an error is seen during the SNMP operations (from the SNMP manager tool), check the switch to verify if this information should really be present. If yes, proceed to step 2.

Step 2 Collect the information from the /svplus/log/configserver.log file when this error occurs. Perform the following:

a.From the configserver.log file, identify the MIB objects that caused the error.

b.Identify the MIB to which these objects belong.

c.Verify whether these MIB objects are supported in this release. If the objects are supported, but still the SNMP agent is not responding for SNMP queries, contact CTM engineers.

Defect Information—Collect the following information for further analysis:

•Complete screen snapshots for the investigative commands used for debugging this issue.

•Configserver.log.

•Related information on the switch.

Possible alternative workaround—None.

J.10.7.2.3 Details, Create, Delete, and Refresh Buttons Are Not Enabled

The Details, Create, Delete, and Refresh buttons are enabled or disabled based on the requirement in the tabular view. These buttons are disabled when a corresponding operation is not supported.

Step 1 Open the /opt/svplus/log/configserver.log file for the MIB.

Step 2 If the Create button is disabled, use any SNMP tool to create the object using the SNMP SET operation.

•If the SNMP SET operation passes, contact CTM engineers.

Cisco Transport Manager Release 6.0 User Guide

 

78-16845-01

J-79

 

Page 78 Page 80
Image 79
Page 78 Page 80
Contents Troubleshooting Conditions that Affect CTM Server Performance Server ProblemsCTM Server Does Not Respond Cannot Connect to the CTM Server NE Connection State Is Listed as Unavailable Snmp Traps Are Not Forwarded from NEs Launching Tables Results in Database ErrorsTrap Port Is Unavailable Performance Monitoring Data Is Not Displayed Problems with ONS 15530 and ONS 15540 ConfigurationCTC-Based NE Is Not Reachable CTC-Based NE Is Not DiscoveredONS 15501, ONS 15540, or ONS 15530 Is Not Reachable Circuit State for Monitor Circuits Reads Duplicate ID Circuits Are Not DisplayedNE Model Type Appears as Unknown Cannot Copy CTC Binary to the CTM Server Memory Backup, Memory Restore, or Software Download FailsGetinfo.sh Script Fails Database Is Not Available Using the get nestate CommandAre the CTM Client and the CTM Server Connected? Database Timeout OccursCannot Log In as Provisioner or Operator Model Index Is Unknown Cannot Authenticate User Message AppearsCTC Fails to Start Cannot Delete an NEAdded a New Software Version to the Wrong NE Cannot Move an NE Between Subnetworks Cannot Delete a SubnetworkCannot Schedule Jobs Bandwidth-Intensive Operations Are Blocked NE Displays Incorrect Configuration Management DataCannot Customize the Network Map Snmptrap How Do I Collect Thread Dumps?Click OK Client Debug Messages How Do I Replace the Alarm Interface Panel?CTM GateWay/TL1 Problems Cisco CRS-1 and Catalyst 6509 Problems CTM Does Not Receive Traps from the Catalyst Cat6509 enable# set snmp trap enable allSyslog CTM Does Not Receive syslog Events from the CatalystCTM Does Not Collect Historical PM Data for the CRS-1 Memory Backup or Restore Fails for the CRS-1 Click NE Service How Do I Configure Telnet on the CRS-1? Cannot Delete an Out-of-Service NE from CTMHow Do I Configure SSH on the CRS-1? How Do I Load a Software Image on the Catalyst 6509? How Do I View the Snmp Configuration on the Catalyst 6509?Output is similar to the following example CTM Cannot Discover an XR 12000 Node Reporting XR 12000 Issues5 XR 12000 PM Collection Issues 4 XR 12000 Alarm and Event Reporting Issues7 XR 12000 NE Explorer Applications Are Disabled 6 XR 12000 BGP and CDP Neighbor Discovery IssuesDiscovery Mechanism Discovery Issues at StartupNo Nodes Are Discovered Node Name Is Incorrect in the Database Output of the switch CLI, selnd, and dbndsNode IP Is Incorrect in the Database Node Alarm Is Shown Incorrectly in the DatabaseCTM State Is Incorrect Reachable Node Is Shown as UnreachableDiscovery Issues at Runtime Collect the output of the switch CLI, selnd, and dbnds Equipment Management Problems Node Mode Remains Ls -ltr *.9 SMCARD01SRM.CF SMCARD01RPM.CF Node Resync Mode IsEMCSnmpFunccProcFuncGenNodeBulkFile1 entering Appendix J Troubleshooting Equipment Management Problems Appendix J Troubleshooting Equipment Management Problems Appendix J Troubleshooting Equipment Management Problems Database Table Population Through Traps and Snmp Upload Appendix J Troubleshooting Equipment Management Problems Appendix J Troubleshooting Equipment Management Problems You should see something like the following Figure J-1shows the end-to-end architecture Figure J-1 CTM End-to-End Architecture Basic Issues Topology Discovery Issues Appendix J Troubleshooting CTM CLI All the Cards Under a Node Are Missing Network Element Discovery IssuesCisco Transport Manager Release 6.0 User Guide 78-16845-01 Appendix J Troubleshooting Alarm Processing Basics Figure J-2 Client/Server Architecture for Alarm Components XML Schema for Alarm RulesFigure J-3 Correlated Alarm Rule Diagram Figure J-5 Transient Alarm Rule Diagram Alarm Severity and Object SeverityCisco Transport Manager Release 6.0 User Guide 78-16845-01 Alarm List Shows Alarm that Does Not Exist on Platform Transient Event Has Disappeared Unexpectedly Chassis View Basics Chassis View ProblemsCard Not Displayed in the Chassis View Lines Not Displayed in the Chassis View10.6.4 DCA/DCB Status Not Displayed on PXM Cards Ethernet Status Not Updated on PXM CardsHIST, CBRX, and Cbtx Status Not Updated in MGX Nodes RPM Card Status Not UpdatedWrong Tooltip Is Displayed Configuration Center ManagementConfiguration Center Framework Lines Not SelectableChoose Tools Configuration Center from any application Cannot Launch the Configuration CenterAppendix J Troubleshooting Configuration Center Management Element Tab-Internal Frame Does Not Launch Element Management-Drag and Drop Within Configuration CenterCross Application-Configuration Center as Drag Source Appendix J Troubleshooting Configuration Center Management XML Parsing Error Configuration Center-Element ManagementDetails, Create, Delete, and Refresh Buttons Are Not Enabled Snmp No Data ErrorSnmp Set Error Snmp Timeout ErrorObject Not Found In Tree View Error Element Data Inconsistent with Switch Configuration Center GUI-Framework Issues Connection Management ProblemsConfig Server Reports Error Messages Appendix J Troubleshooting Connection Management Problems Appendix J Troubleshooting Connection Management Problems Cross Application-Connection List as Drag Source Configuration Centers Connection Tab Does Not Respond Configuration Center GUI-CM Server-Reported ErrorsDATABASEERRORDatabase error %s Appendix J Troubleshooting Connection Management Problems Cmsvr Errors Cannot Create One-Segment Hybrid Unsupported Service Type-General node-slot-port-version TestConn or TestDelay Failed with Switch Error Cmsvr-Connection Diagnostic IssuesConnection Trace Failures Connection Up/Down/Reroute FailedCmgrd Figure J-6 Connection Management Subsystem High-Level Connection Management Subsystem ArchitectureCmgrd-Sdbroker Errors Related key index entries cmgrd, sdbroker, vpi/vci Appendix J Troubleshooting Connection Management Problems 100 Cmgrd Errors101 102 103 Cmgrd-Switch Errors104 105 106 107 Diagnostics Center Problems108 Diagnostics Center Framework109 Cannot Launch Diagnostics Center110 Drop Target Displays Incorrect Object or Object Data Diagnostics Center Does Not Respond GUI Is Grayed Out111 112 Diagnostics Center Server-Specific IssuesSnmpcommtimeout Error While Polling MIB Objects XML Parser Error113 114 Node Sync-Up Status Are Not Shown in the Diagnostics CenterNode Resync Fails Polling of Real-Time Counters FailsUnable to Start, Stop, or Modify Bert Operations Some Real-Time Counters Are Not Shown115 Unable to Start/Stop IMA Link Test Patterns Cannot Perform Connection Diagnostics116 Pmcollector-Generic Troubleshooting Performance Management Collection and Parsing ProblemsPM Collection Issues Miscellaneous Issues or Problems in Diagnostics Center118 119 PM Collection Fails for the Node-Log File Shows Snmp failed120 PM Collection Fails for the Node-Log File Shows Ftp failed121 Statistics Report ProblemsPM Parsing Issues StatsParser-Generic TroubleshootingYou Generated a Report but Do Not See Data for a Long Time You See FDNs for Other Entities when You Generate a ReportStatistics Report You Collected Data but You See No Data Available123 Service Agent ProblemsUtilization Report Value Is Greater than 100% RtmProxyNot Receiving Any Traps Registration with RtmProxy Failed124 125 Audit Trail Logging Mechanism ProblemsManager Gets Deregistered Nodal Community Strings Do Not Work126 Miscellaneous ProblemsAuditLogger.conf Usage Audit Trail Log File Naming Convention127 Nodes Stay in Mode 1 After ColdStartConfig Change or Provisioning Activity Not Reflected on CTM 10.13.1 NTS128 How To Interpret NTS LogData Inconsistency Connection Inconsistency Between the Switch and GUI129 130 Each output line is similar to this131 Process ID of the sdbroker will be returnedInconsistent Connection Secondary Status Inconsistent Connection Status132 133 Incomplete ConnectionsFTP Daemon Overview Generic TroubleshootingFTP Username and Password CTM FTP DaemonFTP Sessions in Switch Cwmftpd-File Not Available On Switch135 10.13.3.8 499 Session Limit Reached 10.13.3.7 421 Session Limit Reached136 137 Failed to Acquire a Session with a SwitchFailed to Acquire Session After All Retries General Log Information138
Related manuals
Manual 68 pages 52.71 Kb
Top Page Image Contents