Polycom 1725-36028-001 manual Press Esc to return to the SpectraLink 8000 System menu

Page 58

Press Esc to return to the SpectraLink 8000 System menu.

SpectraLink 8000 Telephony Gateway Administration Guide

Press Esc to return to the SpectraLink 8000 System menu.

Note that resetting the SpectraLink 8000 Telephony Gateway(s) will terminate any calls in progress on the SpectraLink 8000 Telephony Gateway(s) being reset.

All SpectraLink 8000 Telephony Gateways should be reset at the end of any maintenance procedure that requires any one SpectraLink 8000 Telephony Gateway to be reset either via Maintenance Lock or manually via Reset System. Resetting them all keeps the SpectraLink 8000 Telephony Gateways synchronized, which is important for proper system function.

58	PN: 1725-36028-001_T.doc

Image 58

Contents SpectraLink 8000 Telephony Gateway Administration GuideUtilizing SpectraLink Radio Protocol SRP Copyright Notice Trademark InformationPatent Information Contact InformationReferenced Documents About This GuidePolycom Model Numbers SpectraLink 8000 SVP Server Administration Guide for SRPDeploying Enterprise-Grade Wi-Fi Telephony Customer SupportIcons and Conventions Best Practices Guide for Deploying SpectraLink 8020/8030 WirelessInstallation and Configuration Steps ContentsTelephone Interface Configuration Site Preparation7 SpectraLink 8000 Telephony Gateway Administration 5 Pre-Installation Verification6 Install SpectraLink 8000 Telephony Gateway 8 Connecting to the SpectraLink 8000 TelephonyTelephone Line Configuration Network ConfigurationSet or Change Password Features Programming MenuIndex Troubleshooting via the System Status MenuSafety Notices Wireless Device Planning WorksheetSpectraLink Overview System ArchitectureSpectraLink Voice Priority SVP and Quality of Service System TimingSystem Components SpectraLink Wireless TelephonesSystem Speed SpectraLink 8000 Telephony GatewayEthernet switch Access pointsRouter Administrative computer SpectraLink 8000 SVP ServerSystem Diagram Ethernet switchThe Front Panel of the SpectraLink 8000 Telephony Gateway 4 Timing Master Installation and Configuration Steps ConditionalPage Site Preparation Required MaterialsGrounding materials per section below Grounding Instructions Network infrastructure LAN RequirementsIP addressing Location of SpectraLink 8000 Telephony Gateway and SVP Server Modem administration Telephone Interface ConfigurationPrepare Demarcation Demarc Blocks SpectraLink 8000 Telephony Gateway Administration Guide Assign and Program Telephone Ports Install Telephone Demarc BlocksConnect Telephone Lines to Demarc Blocks 25 PAIR MALE CONNECTOR CABLE TO GATEWAY CONNECTOR A Two-wire analog or digital demarc blockTelephone Ports Telephone Ports Four-wire digital demarc block Connector ATX denotes data transmitted from the telephone system to the Gateway Telephone Four-wire digital demarc block Connector B25 PAIR MALE CONNECTOR CABLE TO GATEWAY CONNECTOR B PortsVerify Pre-Installation Requirements Pre-Installation VerificationCheck Components Page Connector A is… Install SpectraLink 8000 Telephony GatewayMount to Rack or Wall To MountMount the SpectraLink 8000 Telephony Gateway to wall SafetyMount the SpectraLink 8000 Telephony Gateway to rack Grounding instructionsAll system units must be grounded to a protective earth by means of the grounding stud located on the rear panel. Refer to the illustration below for recommended continuity connection Install bonding straps Installing Multiple SpectraLink 8000 Telephony GatewaysMount Gateway Install IPC cables Connect SpectraLink 8000 Telephony Gateway to Demarc Blocks Connect powerConnect five or more SpectraLink 8000 Telephony Gateways Connect SpectraLink 8000 Telephony Gateway to LANStatus 1 should be blinking on each SpectraLink 8000 Telephony Gateway Page SpectraLink 8000 Telephony Gateway Administration Overview SpectraLink 8000 Telephony Gateway Administration Guide SpectraLink 8000 Telephony Gateway Configuration Sequence Send All 11. Perform AP coverage test per Certifying the Wireless TelephonesTo Perform this Function Navigating through the Administration Console ScreensPress Page Connecting to the SpectraLink 8000 Telephony Gateway Connect via the Serial PortSelect a SpectraLink 8000 Telephony Gateway to Administer If using a serial connection, only the SpectraLink 8000 Telephony Gateway that is connected via the serial cable is shown 5. Unplug the serial cable Connecting via Telnet Connecting via External ModemConfigure modem internal settings US Robotics Sportster Connecting via Internal Modem Connect the modemPage Menu Option Main MenuFunction Page Network Configuration Subnet Mask The network administrator must define the subnet mask correct setting from the DHCP server. The DHCP setting is only valid when the IP address is also acquired using DHCP Press Esc to return to the SpectraLink 8000 System menu Set or Change Password Page SpectraLink 8000 Telephony Gateway Configuration OAI hostname Valid entries Valid source location entries are Press Esc to return to the NetLink Wireless Telephone System menu Reset the SpectraLink 8000 Telephony Gateway Page Telephone Line Configuration Adding or Changing a Handset3. Write the MAC address on the Wireless Planning Device Worksheet 3. Press D to delete the handset information Deleting a Handset2. Use the arrow keys to highlight the line to be deleted 4. Press Y to accept changesPage Features Programming Menu Page Feature Programming no Softkeys Programming Analog PBX Features Programming Digital PBX FeaturesInterface Guide for your system 3. Type F to assign the FLASH function Programming the ADMIN Feature Menu Programming no softkeys To change the menu settings 4. Repeat for each menu as needed Page Softkey and Shortcut Key Programming Sample screen Scroll to remaining options Speakerphone softkey programming SpectraLink 8020/8030 only Softkey Label Software Maintenance Software UpdatesFTP procedure Using FTPUpdating Larger Systems To transfer the software using FTP Updating Wireless Telephone Software Normal download messagesBackup and Restore SpectraLink 8000 Telephony Gateway Configuration Download failure or recovery messagesget config.bin gateway1.bin Troubleshooting via the System Status Menu Error Status Displays alarm and error message information Access Point Status Unless noted otherwise, times are displayed using the format Error StatusD is day, HH is hours, MM is minutes, and SS is seconds Alarm Error DescriptionReset = reset SpectraLink 8000 Telephony Gateway Alarm 1 SpectraLink Radio Protocol See Network Status section Network Status RX Broadcast The number of broadcast packets and bytes received Telephone Line Status Wireless Telephone Status WT MAC The MAC address of the handset Software Version Wireless Telephones per AP Wireless Device Planning WorksheetHost Switch Type Switch Port ID IP AddressSpectraLink 8000 Telephony Gateway Administration Guide Safety Notices Page Index