Peavey IA 200V, IA 800V, IA 400V, IA Series owner manual IA 200 Specifications

Page 13

Rated Power (2 x 4 ohms):

150 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD

Rated Power (2 x 8 ohms): 100 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD

Rated Power (1 x 4 ohms):

160 watts @ 1 kHz at < 0.01% THD

Rated Power (1 x 8 ohms):

110 watts @ 1 kHz at < 0.005% THD

Minimum load impedance: 4 ohms

Maximum RMS Voltage Swing: 35 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

10 Hz - 100 kHz; +0, -3 dB at rated power

THD (2 x 4 ohms):

<0.05% @ 150W from 20 Hz - 20kHz with both channels driven

THD (2 x 8 ohms):

<0.05% @ 100W from 20 Hz - 20kHz with both channels driven

THD (1 x 4 ohms):

< 0.01% @ 170W @ 1 kHz

THD (1 x 8 ohms):

< 0.005% @ 110W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 70 kHz, 150W @

4 ohms

IA200 SPECIFICATIONS

Slew Rate:

-25V/µs

Damping Factor (8 ohms): > 550:1 @ 20 Hz -1 kHz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity (x40):

.61 volts @ ohms, .71 volts @ 8 ohms

Input Sensitivity (x20):

1.23volts @ 4 ohms, 1.4 volts @ 8 ohms

Input Impedance: 20 k

Hum and Noise:

>-105 dB, “A” weighted referenced to rated power

Crosstalk:

>-75 dB, “A” weighted referenced to rated power @ 8 ohms

Current Draw @ 1/8 power:

330 watts @ 4 ohms, 230 watts @

8 ohms

Current Draw @ 1/3 power:

550 watts @ 4 ohms, 330 watts @

8 ohms

Idle Current Draw:

25 watts in Standby Mode

Maximum Current Draw:

800 watts @ 4 ohms, 510 watts @

8 ohms

Thermal Emissions (btu/hr.): 1,364 @ 1/3 power 4 ohms, 443 @ 1/3 power 8 ohms

Cooling:

80mm DC fan, off until heatsinks reach 45o C, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power, 4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

3.48" x 19" x 16.4" (15.8" behind rear mounting ears)

88.4mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight:

33 lbs. (15 kg)

Net Weight:

29.6 lbs. (13.4 kg)

TM®

Due to our efforts for constant improvements,

features and specifications listed herein are subject to change without notice.

13

Image 13
Contents Series Power Amplifiers Precautions Table of Contents Installation and Mounting Amplifier ConfigurationTo SET UP the Amplifier for Basic Usage IntroductionFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Protection Features Signal Ground ConnectionSequential TURN-ON/TURN-OFF Sequential TURN-ON/TURN-OFF WiringAWG Wire Gauge ChartIA 200 Specifications IA 200V Specifications Rated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005% IA 400 SpecificationsGross Weight 33.6 lbs .25 kg Net Weight Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input CmrrIA 400V Specifications Rated Power 2 X 8 ohms IA 800 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight THD 1 X 8 ohms 0.005% @ 425W @ 1 kHzCurrent Draw @ 1/8 power IA 800V-70 765 watts IA 800V SpecificationsCurrent Draw @ 1/3 power IA 800V-70 1,100 watts Minimum Load Impedance IA 800V-70 12.5 ohmsImportant Safety Instructions Configuración DEL Amplificador Para LA Utilización Básica Configuración DEL AmplificadorIntroducción DesembalajePage Características Delpanel Frontal Características Delpanel Posterior Operación Conexiones DEL Módulo DE Entrada Configuración DEL Modo DE SeñalConexiones DE Salida DE Altavoces Puentes DE Selección DE GananciaCompartimiento DE Control DE Amplificadores Desmontaje DE MódulosLimitador DE Recorte Funciones DE ProtecciónProtección Térmica CortocircuitosPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Distorsión armónica total dos canales amplificados Mínima impedancia de carga IA 200V-70 50 WDistorsión armónica total un canal amplificado Distorsión por intermodulación según norma SmptePotencia nominal 2 x 8 W Potencia nominal 2 x 4 WDistorsión armónica total 2 x 4 W Distorsión armónica total 2 x 8 WPeso neto 14,06 kg Consumo máximo de corriente IA% 60 Hz y 7 kHz, 600 W a 4 W % a 600 W desde 20 Hz hasta KHz con señal en ambos canalesA 4 W, 1,41 V a 8 W A 4 W, 2,83 V a 8 WDisipación térmica BTU/h IA Ancho de banda de potencia IAPeso neto 20,41 kg ¡GUARDE Estas Instrucciones Instrucciones DE Seguridad ImportantesInstallation Configuration DES AmplificateursIntroduction ’OUVERTUREFace Avant Pattes DE Montage EN Rack LED SignalSélecteur DE Mise Sous Tension Trois Positions LED D’ALIMENTATIONModule D’ENTRÉE Face Arriere Modules D’ENTREE ET DE CommunicationBornier DE Sortie CommunicationsUtilisation Cavaliers DE Selection DE Gain Emplacement Pour ModuleConnexions DES HAUT-PARLEURS Manipulation D’UN ModuleLoad Fault Correction Correction DE Faute DE Charge Connexion DE LA Masse DU SignalEnlever OU Remplacer UN Module ProtectionsProtection Tension Continue COURT-CIRCUITSequence TURN-ON/TURN-OFF Connexions TURN-ON/TURN-OFF SéquentielTable DE Section DES Câbles Rated Ppwer 1 x 4 ohms Caractéristiques IASlew Rate -25V/µs Damping Factor 8 ohms Max. Current DrawMaximum RMS Voltage Swing Minimum Load Impedance IA 200V-70 50 ohmsTHD one channel driven IA Watts @ 4 ohms, 1,010 watts @ Ohms 05% @ 200W from 20 Hz KHz with both channels drivenWatts @ 1/3 power IA 472 @ 1/3 power Max Current Draw Indicator LEDsVoltage Gain Cooling X40 32 dB standard, x20 26 dBDamping Factor 8 ohms Rated Power 2 x 8 ohms Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hrRated Power 1 x 4 ohms Controls Frequency Response Input Impedance ConnectorsMax Current Draw 15% @ 400W from 20 Hz to KHz with both channels driven IAImportant Safety Instructions SET UP FÜR DEN Einfachen Gebrauch Installation UND MontageEinführung AuspackenAC Netzschalter MIT 3 Positionen Front Panel Features Chassis FÜR DIE RackmontageLED-ANZEIGE SCHUTZ-LEDEINGANGS-MODULE Anschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULELS Anschlussleiste KommunikationsschachtBetrieb Gain Select Jumper Signal Mode KonfigurationLautsprecher Ausgänge Verstärker Steuerschacht Signal ERDUNGS-VERBINDUNGModul Entfernen Entfernen Oder Austauschen Eines ModulesDC Spannungsschutz ÜberhitzungsschutzEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen Leistungsbandbreite IA 400V SpezifikationenEingangs Cmrr NettogewichtIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation