Peavey IA 200V, IA 800V, IA 400V Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hr

Page 49

CARACTÉRISTIQUES IA ™ 800

Rated Power (2 x 4 ohms):

Slew Rate:

Thermal Emissions (BTU/hr.):

600 watts @ 20 Hz - 20 kHz, both

30V/µs

4,603 @ 1/3 power 4 ohms, 3,012 @

channels driven at < 0.1% THD

 

1/3 power 8 ohms

 

Damping Factor (8 ohms):

 

Rated Power (2 x 8 ohms):

> 350:1 @ 20 Hz - 1 kHz

Cooling

400 watts @ 20 Hz - 20 kHz, both

 

120mm DC fan, off until heatsinks

channels driven at < 0.05% THD

Input CMRR:

reach 45° C, then variable speed

 

> -65 dB @ 1 kHz

 

Rated Power (1 x 4 ohms):

 

Controls:

70 watts @ 1 kHz at < 0.008% THD

Voltage Gain:

2 rear panel attenuators, sequential

 

x40 (32 dB) standard, x20 (26 dB)

turn on/off

Rated Power (1 x 8 ohms):

internally jumper-selectable

 

425 watts @ 1 kHz at < 0.005% THD

 

Indicator LEDs:

 

Input Sensitivity (x40):

2 Clip, 2 Signal, 2 LFC, 1 Protect,

Minimum Load Impedance:

1.22 volts @ 4 ohms, 1.41 volts @ 8

1 Power

4 ohms

ohms

 

 

 

Protection:

Maximum RMS Voltage Swing:

INPUT SENSITIVITY (X20):

Temp., DC, turn-on bursts, subsonic,

70 volts

2.5 volts @ 4 ohms, 2.83 volts @ 8

incorrect load or short

 

ohms

 

Frequency Response:

Input Impedance:

Connectors:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

20 k ohms, balanced

8-pin plugable signal input, 4-pin

 

 

plugable sequential power,

Power Bandwidth:

Hum and Noise:

4-terminal barrier strip, IEC AC power

10 Hz - 100 kHz; +0, -3 dB at rated

> -110 dB, “A” weighted referenced to

connector

power

rated power

 

 

 

Construction:

THD (2 x 4 ohms):

Crosstalk:

18 ga. steel reinforced with 12 ga.

< 0.1% @ 600W from 20 Hz - 20 kHz

> -65 dB, “A” weighted referenced to

rack ears, extruded aluminum front

with both channels driven

rated power

panel

THD (2 x 8 ohms):

Current Draw @ 1/8 power:

Dimensions:

< 0.05% @ 400W from 20 Hz -

950 watts @ 4 ohms, 725 watts @

5.25" x 19" x 16.4" (15.8" behind

20 kHz with both channels driven

8 ohms

rear mounting ears)

 

 

133mm x 483mm x 416.6mm

THD (1 X 4 ohms):

Current Draw @ 1/3 power:

(401mm behind rear mounting ears)

< 0.008% @ 700W @ 1 kHz

1,750 watts @ 4 ohms, 1,150 watts

 

 

@ 8 ohms

Gross Weight:

THD (1 X 8 ohms):

 

51.4 lbs. (23.3 kg)

< 0.005% @ 425W @ 1 kHz

Idle Current Draw:

 

 

32 watts in Standby Mode

Net Weight:

SMPTE IMD:

 

45 lbs. (20.41 kg)

< 0.1% 60 Hz and 7 kHz, 600W @

Max. Current Draw:

 

4 ohms

2,670 watts @ 4 ohms (time limited

 

 

by breaker), 1,725 watts @ 8 ohms

 

®

TM

Etant donnés nos efforts constants pour l’amélioration de notre matériel,

les caractéristiques et spécifications listée ici peuvent être modifiées sans préavis.

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Series Power Amplifiers Precautions Table of Contents Installation and Mounting Amplifier ConfigurationTo SET UP the Amplifier for Basic Usage IntroductionFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Protection Features Signal Ground ConnectionSequential TURN-ON/TURN-OFF Sequential TURN-ON/TURN-OFF WiringAWG Wire Gauge ChartIA 200 Specifications IA 200V Specifications Rated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005% IA 400 SpecificationsGross Weight 33.6 lbs .25 kg Net Weight Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input CmrrIA 400V Specifications Rated Power 2 X 8 ohms IA 800 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight THD 1 X 8 ohms 0.005% @ 425W @ 1 kHzCurrent Draw @ 1/8 power IA 800V-70 765 watts IA 800V SpecificationsCurrent Draw @ 1/3 power IA 800V-70 1,100 watts Minimum Load Impedance IA 800V-70 12.5 ohmsImportant Safety Instructions Configuración DEL Amplificador Para LA Utilización Básica Configuración DEL AmplificadorIntroducción DesembalajePage Características Delpanel Frontal Características Delpanel Posterior Operación Conexiones DEL Módulo DE Entrada Configuración DEL Modo DE SeñalConexiones DE Salida DE Altavoces Puentes DE Selección DE GananciaCompartimiento DE Control DE Amplificadores Desmontaje DE MódulosLimitador DE Recorte Funciones DE ProtecciónProtección Térmica CortocircuitosPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Distorsión armónica total dos canales amplificados Mínima impedancia de carga IA 200V-70 50 WDistorsión armónica total un canal amplificado Distorsión por intermodulación según norma SmptePotencia nominal 2 x 8 W Potencia nominal 2 x 4 WDistorsión armónica total 2 x 4 W Distorsión armónica total 2 x 8 WPeso neto 14,06 kg Consumo máximo de corriente IA% 60 Hz y 7 kHz, 600 W a 4 W % a 600 W desde 20 Hz hasta KHz con señal en ambos canalesA 4 W, 1,41 V a 8 W A 4 W, 2,83 V a 8 WDisipación térmica BTU/h IA Ancho de banda de potencia IAPeso neto 20,41 kg ¡GUARDE Estas Instrucciones Instrucciones DE Seguridad ImportantesInstallation Configuration DES AmplificateursIntroduction ’OUVERTUREFace Avant Pattes DE Montage EN Rack LED SignalSélecteur DE Mise Sous Tension Trois Positions LED D’ALIMENTATIONModule D’ENTRÉE Face Arriere Modules D’ENTREE ET DE CommunicationBornier DE Sortie CommunicationsUtilisation Cavaliers DE Selection DE Gain Emplacement Pour ModuleConnexions DES HAUT-PARLEURS Manipulation D’UN ModuleLoad Fault Correction Correction DE Faute DE Charge Connexion DE LA Masse DU SignalEnlever OU Remplacer UN Module ProtectionsProtection Tension Continue COURT-CIRCUITSequence TURN-ON/TURN-OFF Connexions TURN-ON/TURN-OFF SéquentielTable DE Section DES Câbles Rated Ppwer 1 x 4 ohms Caractéristiques IASlew Rate -25V/µs Damping Factor 8 ohms Max. Current DrawMaximum RMS Voltage Swing Minimum Load Impedance IA 200V-70 50 ohmsTHD one channel driven IA Watts @ 4 ohms, 1,010 watts @ Ohms 05% @ 200W from 20 Hz KHz with both channels drivenWatts @ 1/3 power IA 472 @ 1/3 power Max Current Draw Indicator LEDsVoltage Gain Cooling X40 32 dB standard, x20 26 dBDamping Factor 8 ohms Rated Power 2 x 8 ohms Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hrRated Power 1 x 4 ohms Controls Frequency Response Input Impedance ConnectorsMax Current Draw 15% @ 400W from 20 Hz to KHz with both channels driven IAImportant Safety Instructions SET UP FÜR DEN Einfachen Gebrauch Installation UND MontageEinführung AuspackenAC Netzschalter MIT 3 Positionen Front Panel Features Chassis FÜR DIE RackmontageLED-ANZEIGE SCHUTZ-LEDEINGANGS-MODULE Anschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULELS Anschlussleiste KommunikationsschachtBetrieb Gain Select Jumper Signal Mode KonfigurationLautsprecher Ausgänge Verstärker Steuerschacht Signal ERDUNGS-VERBINDUNGModul Entfernen Entfernen Oder Austauschen Eines ModulesDC Spannungsschutz ÜberhitzungsschutzEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen Leistungsbandbreite IA 400V SpezifikationenEingangs Cmrr NettogewichtIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation
Top Page Image Contents