Peavey IA 200V, IA 400V, IA Series owner manual IA 800V Spezifikationen

Page 65

IA800V SPEZIFIKATIONEN

Leistung (2 Kanäle):

400 Watt @ 20 Hz bis 20 kHz beide Kanäle getrieben an < 0.1% THD

Leistung (1 Kanal):

415 Watt @ 1 kHz an < 0.01% THD

Minimale Last Impedanz:

IA 800V-70: 12.5 Ohm

IA 800V-100: 25 Ohm

Maximale RMS

Spannungsschwingung:

IA 800V-70: 85 Volt

IA 800V-100: 110 Volt

Frequenzgang:

10 Hz - 25 kHz; +0, -.3 dB an 1 Watt

Leistungs-Bandbreite:

IA 800V-70:

10 Hz - 100 kHz; +0, -3 dB bei angegebener Leistung

IA 800V-100:

10 Hz - 50 kHz; +0, -3 dB bei angegebener Leistung

THD (zwei Kanäle getrieben): IA 800V-70:

< 0.15% @ 400W von 20 Hz bis

20 kHz mit beiden Kanälen getrieben IA 800V-100:

< 0.1% @ 400W von 20 Hz bis

20 kHz mit beiden Kanälen getrieben

THD (1 Kanal getrieben): < 0.008% @ 400W @ 1 kHz

SMPTE IMD:

< 0.1% 60 Hz und 7 kHz, @ 400W

Slew Rate:

35V/µs

Dämpfungsfaktor:

> 400:1 @ 20 Hz - 400 Hz

CMRR Eingang :

> -65 dB @ 1 kHz

Leistungs Gain:

x40 (32 dB) Standard, x20 (26 dB) intern pere Jumper wählbarl

Eingangs-Empfindlichkeit:

IA 800V-70:

1.77Volt oder 3.54 für empfohlenen Ausgang

IA 800V-100:

2.5Volt oder 5 Volt für empfohlenen Ausgang

Eingangs-Impedanz:

20 k Ohm, balanciert

Brummen und Rauschen:

>-108 dB, “A” gewichtet, bezogen auf angegebene Leistung

Nebensprechen:

>-65 dB, “A” gewichtet, bezogen auf angegebene Leistung

Stromaufnahme @ 1/8 Leistung:

IA 800V-70: 765 Watt

IA 800V-100: 775 Watt

Stromaufnahme @ 1/3 Leistung:

IA 800V-70: 1,100 Watt

IA 800V-100: 1,150 Watt

Stromaufnahme im Leerlauf:

45 Watt im Standby Modus

Max Stromaufnahme:

IA 800V-70:

1,680 Watt für angegebene Leistung IA 800V-100:

1,700 Watt für angegebene Leistung

Thermale Ausscheidungen (BTU/hr.):

IA 800V-70:

2,841 Watt @ 1/3 Leistung

IA 800V-100:

3,015 Watt @ 1/3 Leistung

Kühlung:

120mm DC Lüfter, ausgeschaltet bis Kühlkörper 45oC erreicht,

dann variable Geschwindigkeit

Regler:

2 rückseitige Dämpfer, sequentielles Ein-/Ausschalten

Anzeige-LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Schutz,

1 Leistungs-LED

Schutz:

2 Clip, 2 Signal, 2 LFC, 1 Schutz,

1 Leistungs-LED

Anschlüsse:

8-Pin Signal-Eingang (steckbar),

4-Pin seq. Einschaltfolge (steckbar),

4-Pol Klemmleiste, IEC AC Netzanschluss-Buchse

Konstruktion:

18 ga. stahlverstärkt mit 12 ga. Anschlußlaschen, extrudiertes Aluminium-Frontpanel

Maße:

133mm x 483mm x 416.6mm (401mm hinter Anschlusslaschen)

Brutto-Gewicht:

(23.3 kg.)

Netto-Gewicht:

(20.41 kg.)

®

TM

Da wir ständig um Verbesserungen bemüht sind, unterliegen die hier aufgelisteten Features und Spezifikationen Änderungen ohne

vorheriger Ankündigung.

65

Image 65
Contents Series Power Amplifiers Precautions Table of Contents Installation and Mounting Amplifier ConfigurationTo SET UP the Amplifier for Basic Usage IntroductionFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Protection Features Signal Ground ConnectionSequential TURN-ON/TURN-OFF Sequential TURN-ON/TURN-OFF WiringAWG Wire Gauge ChartIA 200 Specifications IA 200V Specifications Rated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005% IA 400 SpecificationsGross Weight 33.6 lbs .25 kg Net Weight Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input CmrrIA 400V Specifications Rated Power 2 X 8 ohms IA 800 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight THD 1 X 8 ohms 0.005% @ 425W @ 1 kHzCurrent Draw @ 1/8 power IA 800V-70 765 watts IA 800V SpecificationsCurrent Draw @ 1/3 power IA 800V-70 1,100 watts Minimum Load Impedance IA 800V-70 12.5 ohmsImportant Safety Instructions Configuración DEL Amplificador Para LA Utilización Básica Configuración DEL AmplificadorIntroducción DesembalajePage Características Delpanel Frontal Características Delpanel Posterior Operación Conexiones DEL Módulo DE Entrada Configuración DEL Modo DE SeñalConexiones DE Salida DE Altavoces Puentes DE Selección DE GananciaCompartimiento DE Control DE Amplificadores Desmontaje DE MódulosLimitador DE Recorte Funciones DE ProtecciónProtección Térmica CortocircuitosPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Distorsión armónica total dos canales amplificados Mínima impedancia de carga IA 200V-70 50 WDistorsión armónica total un canal amplificado Distorsión por intermodulación según norma SmptePotencia nominal 2 x 8 W Potencia nominal 2 x 4 WDistorsión armónica total 2 x 4 W Distorsión armónica total 2 x 8 WPeso neto 14,06 kg Consumo máximo de corriente IA% 60 Hz y 7 kHz, 600 W a 4 W % a 600 W desde 20 Hz hasta KHz con señal en ambos canalesA 4 W, 1,41 V a 8 W A 4 W, 2,83 V a 8 WPeso neto 20,41 kg Ancho de banda de potencia IADisipación térmica BTU/h IA ¡GUARDE Estas Instrucciones Instrucciones DE Seguridad ImportantesInstallation Configuration DES AmplificateursIntroduction ’OUVERTUREFace Avant Pattes DE Montage EN Rack LED SignalSélecteur DE Mise Sous Tension Trois Positions LED D’ALIMENTATIONModule D’ENTRÉE Face Arriere Modules D’ENTREE ET DE CommunicationBornier DE Sortie CommunicationsUtilisation Cavaliers DE Selection DE Gain Emplacement Pour ModuleConnexions DES HAUT-PARLEURS Manipulation D’UN ModuleLoad Fault Correction Correction DE Faute DE Charge Connexion DE LA Masse DU SignalEnlever OU Remplacer UN Module ProtectionsProtection Tension Continue COURT-CIRCUITSequence TURN-ON/TURN-OFF Connexions TURN-ON/TURN-OFF SéquentielTable DE Section DES Câbles Rated Ppwer 1 x 4 ohms Caractéristiques IASlew Rate -25V/µs Damping Factor 8 ohms Max. Current DrawTHD one channel driven IA Minimum Load Impedance IA 200V-70 50 ohmsMaximum RMS Voltage Swing Watts @ 4 ohms, 1,010 watts @ Ohms 05% @ 200W from 20 Hz KHz with both channels drivenWatts @ 1/3 power IA 472 @ 1/3 power Max Current Draw Indicator LEDsVoltage Gain Cooling X40 32 dB standard, x20 26 dBDamping Factor 8 ohms Rated Power 2 x 8 ohms Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hrRated Power 1 x 4 ohms Controls Frequency Response Input Impedance ConnectorsMax Current Draw 15% @ 400W from 20 Hz to KHz with both channels driven IAImportant Safety Instructions SET UP FÜR DEN Einfachen Gebrauch Installation UND MontageEinführung AuspackenAC Netzschalter MIT 3 Positionen Front Panel Features Chassis FÜR DIE RackmontageLED-ANZEIGE SCHUTZ-LEDEINGANGS-MODULE Anschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULELS Anschlussleiste KommunikationsschachtBetrieb Lautsprecher Ausgänge Signal Mode KonfigurationGain Select Jumper Verstärker Steuerschacht Signal ERDUNGS-VERBINDUNGModul Entfernen Entfernen Oder Austauschen Eines ModulesEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten ÜberhitzungsschutzDC Spannungsschutz Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen Leistungsbandbreite IA 400V SpezifikationenEingangs Cmrr NettogewichtIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation