Peavey IA 800V, IA 200V, IA Series owner manual IA 400V Specifications

Page 16

IA™ 400V SPECIFICATIONS

Rated Power (two channels): 200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (one channel): 215 watts @ 1 kHz at < 0.0075%

THD

Minimum Load Impedance: IA 400V-70: 25 ohms

IA 400V-100: 50 ohms

Maximum RMS Voltage Swing: IA 400V-70: 86 volts

IA 400V-100: 116 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

IA 400V-70:

10 Hz - 100 kHz; +0, -3 dB at rated power

IA 400V-100:

10 Hz - 50 kHz; +0, -.3 dB at rated power

THD (two channels driven): IA 400V-70:

<0.1% @ 200W from 20 Hz - 20 kHz with both channels driven

IA 400V-100:

<0.15% @ 200W from 20 Hz - 20 kHz with both channels driven

THD (one channel driven):

IA 400V-70:

<0.005% @ 200W @ 1 kHz IA 400V-100:

<0.015% @ 200W @ 1 kHz

SMPTE IMD:

< 0.1% 60 Hz and 7 kHz, 200W

Slew Rate:

IA 400V-70: 30V/µs

IA 400V-100: 40V/µs

Damping Factor:

IA 400V-70:

>1,000:1 @ 20 Hz - 400 Hz IA 400V-100:

>2,000:1 @ 20 Hz - 400 Hz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity:

IA 400V-70:

1.77volts or 3.54 volts for rated output

IA 400V-100:

2.5volts or 5 volts for rated output

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-110 dB, “A” weighted referenced to rated power

Crosstalk:

IA 400V-70:

>-70 dB, “A” weighted referenced to rated power

IA 400V-100:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power: IA 400V-70: 415 watts

IA 400V-100: 385 watts

Current Draw @ 1/3 power: IA 400V-70: 600 watts

IA 400V-100: 565 watts

Idle Current Draw:

IA 400V-70:

38 watts in Standby Mode IA 400V-100:

43 watts in Standby Mode

Maximum Current Draw:

IA 400V-70:

970 watts for rated power IA 400V-100:

840 watts for rated power

Thermal Emissions (BTU/hr.):

IA 400V-70:

1591 watts @ 1/3 power IA 400V-100:

1472 @ 1/3 power

Cooling:

80mm DC fan, off until heatsinks reach 45oC, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

3.48" x 19" x 16.4" (15.8" rear mounting ears)

88.4mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight: 33.5 lbs. (15.2 kg.)

Net Weight:

31 lbs. (14.06 kg.)

®

TM

Due to our efforts for constant improvements,

features and specifications listed herein are subject to change without notice.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Series Power Amplifiers Precautions Table of Contents Amplifier Configuration Installation and MountingTo SET UP the Amplifier for Basic Usage IntroductionFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Signal Ground Connection Protection FeaturesSequential TURN-ON/TURN-OFF Wiring Sequential TURN-ON/TURN-OFFWire Gauge Chart AWGIA 200 Specifications IA 200V Specifications IA 400 Specifications Rated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005%Gross Weight 33.6 lbs .25 kg Net Weight Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input CmrrIA 400V Specifications IA 800 Specifications Rated Power 2 X 8 ohmsGross Weight 51.4 lbs .3 kg Net Weight THD 1 X 8 ohms 0.005% @ 425W @ 1 kHzIA 800V Specifications Current Draw @ 1/8 power IA 800V-70 765 wattsCurrent Draw @ 1/3 power IA 800V-70 1,100 watts Minimum Load Impedance IA 800V-70 12.5 ohmsImportant Safety Instructions Configuración DEL Amplificador Configuración DEL Amplificador Para LA Utilización BásicaIntroducción DesembalajePage Características Delpanel Frontal Características Delpanel Posterior Operación Configuración DEL Modo DE Señal Conexiones DEL Módulo DE EntradaPuentes DE Selección DE Ganancia Conexiones DE Salida DE AltavocesCompartimiento DE Control DE Amplificadores Desmontaje DE MódulosFunciones DE Protección Limitador DE RecorteProtección Térmica CortocircuitosPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Mínima impedancia de carga IA 200V-70 50 W Distorsión armónica total dos canales amplificadosDistorsión armónica total un canal amplificado Distorsión por intermodulación según norma SmptePotencia nominal 2 x 4 W Potencia nominal 2 x 8 WDistorsión armónica total 2 x 4 W Distorsión armónica total 2 x 8 WConsumo máximo de corriente IA Peso neto 14,06 kg% a 600 W desde 20 Hz hasta KHz con señal en ambos canales % 60 Hz y 7 kHz, 600 W a 4 WA 4 W, 1,41 V a 8 W A 4 W, 2,83 V a 8 WDisipación térmica BTU/h IA Ancho de banda de potencia IAPeso neto 20,41 kg Instrucciones DE Seguridad Importantes ¡GUARDE Estas InstruccionesConfiguration DES Amplificateurs InstallationIntroduction ’OUVERTURELED Signal Face Avant Pattes DE Montage EN RackSélecteur DE Mise Sous Tension Trois Positions LED D’ALIMENTATIONFace Arriere Modules D’ENTREE ET DE Communication Module D’ENTRÉEBornier DE Sortie CommunicationsUtilisation Emplacement Pour Module Cavaliers DE Selection DE GainConnexions DES HAUT-PARLEURS Manipulation D’UN ModuleConnexion DE LA Masse DU Signal Load Fault Correction Correction DE Faute DE ChargeEnlever OU Remplacer UN Module ProtectionsCOURT-CIRCUIT Protection Tension ContinueSequence TURN-ON/TURN-OFF Connexions TURN-ON/TURN-OFF SéquentielTable DE Section DES Câbles Caractéristiques IA Rated Ppwer 1 x 4 ohmsSlew Rate -25V/µs Damping Factor 8 ohms Max. Current DrawMaximum RMS Voltage Swing Minimum Load Impedance IA 200V-70 50 ohmsTHD one channel driven IA 05% @ 200W from 20 Hz KHz with both channels driven Watts @ 4 ohms, 1,010 watts @ OhmsMax Current Draw Indicator LEDs Watts @ 1/3 power IA 472 @ 1/3 powerVoltage Gain Cooling X40 32 dB standard, x20 26 dBRated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hr Damping Factor 8 ohms Rated Power 2 x 8 ohmsRated Power 1 x 4 ohms Controls Frequency Response Input Impedance Connectors15% @ 400W from 20 Hz to KHz with both channels driven IA Max Current DrawImportant Safety Instructions Installation UND Montage SET UP FÜR DEN Einfachen GebrauchEinführung AuspackenFront Panel Features Chassis FÜR DIE Rackmontage AC Netzschalter MIT 3 PositionenLED-ANZEIGE SCHUTZ-LEDAnschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULE EINGANGS-MODULELS Anschlussleiste KommunikationsschachtBetrieb Gain Select Jumper Signal Mode KonfigurationLautsprecher Ausgänge Signal ERDUNGS-VERBINDUNG Verstärker SteuerschachtModul Entfernen Entfernen Oder Austauschen Eines ModulesDC Spannungsschutz ÜberhitzungsschutzEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen IA 400V Spezifikationen LeistungsbandbreiteEingangs Cmrr NettogewichtIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation
Top Page Image Contents