Peavey IA 200 IA 800 Specifications, Rated Power 2 X 8 ohms, THD 1 X 8 ohms 0.005% @ 425W @ 1 kHz

Rated Power (2 X 4 ohms):

600 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD

Rated Power (2 X 8 ohms):

400 watts @ 20 Hz - 20 kHz, both channels driven at < 0.05% THD

Rated Power (1 X 4 ohms):

70 watts @ 1 kHz at < 0.008% THD

Rated Power (1 X 8 ohms):

425 watts @ 1 kHz at < 0.005% THD

Minimum Load Impedance: 4 ohms

Maximum RMS Voltage Swing: 70 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

10 Hz - 100 kHz; +0, -3 dB at rated power

THD (2 x 4 ohms):

<0.1% @ 600W from 20 Hz - 20 kHz with both channels driven

THD (2 x 8 ohms):

<0.05% @ 400W from 20 Hz - 20 kHz with both channels driven

THD (1 X 4 ohms):

< 0.008% @ 700W @ 1 kHz

THD (1 X 8 ohms): <0.005% @ 425W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 7 kHz, 600W @

4 ohms

Slew Rate:

30V/µs

IA™ 800 SPECIFICATIONS

Damping Factor (8 ohms): > 350:1 @ 20 Hz - 1 kHz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity (x40):

1.22volts @ 4 ohms, 1.41 volts @ 8 ohms

Input Sensitivity (X20):

2.5volts @ 4 ohms, 2.83 volts @ 8 ohms

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-110 dB, “A” weighted referenced to rated power

Crosstalk:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power:

950 watts @ 4 ohms, 725 watts @

8 ohms

Current Draw @ 1/3 power:

1,750 watts @ 4 ohms, 1,150 watts @ 8 ohms

Idle Current Draw:

32 watts in Standby Mode

Maximum Current Draw:

2,670 watts @ 4 ohms (time limited by breaker), 1,725 watts @ 8 ohms

Thermal Emissions (BTU/hr.): 4,603 @ 1/3 power 4 ohms, 3,012 @ 1/3 power 8 ohms

Cooling

120mm DC fan, off until heatsinks reach 45° C, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

5.25" x 19" x 16.4" (15.8" behind rear mounting ears)

133mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight: 51.4 lbs. (23.3 kg)

Net Weight:

45 lbs. (20.41 kg)

TM®

Due to our efforts for constant improvements,

features and specifications listed herein are subject to change without notice.

17