Peavey IA 800V, IA 200V, IA 400V, IA Series owner manual IA 800 Spezifikationen

Page 64

Leistung (2 X 4 ohm):

600 Watt @ 20 Hz bis 20 kHz, beide Kanäle getrieben an < 0.1% THD

Leistung (2 X 8 ohm):

400 Watt @ 20 Hz to 20 kHz, beide Kanäle getrieben an < 0.05% THD

Empfohlene Leistung (1 X 4 Ohm):

70 Watt @ 1 kHz an < 0.008% THD

Empfohlene Leistung (1 X 8 Ohm): 425 watts @ 1 kHz an < 0.005% THD

Minimale Last Impedanz: 4 ohms

Maximum RMS

Spannungsschwingung:

70 Volt

Frequenzgang:

10 Hz - 25 kHz; +0, -.3 dB an 1 Watt

Leistungsbrandbreite:

10 Hz - 100 kHz; +0, -3 dB bei angegebener Leistung

THD (2 x 4 ohm):

<0.1% @ 600W von 20 Hz bis 20 kHz mit beiden Kanälen getrieben

THD (2 x 8 ohm):

< 0.05% @ 400W von 20 Hz bis

20 kHz mit beiden Kanälen getrieben

THD (1 X 4 ohm):

< 0.008% @ 700W @ 1 kHz

THD (1 X 8 ohm):

< 0.005% @ 425W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz und 7 kHz, 600W @

4 Ohm

Slew Rate:

30V/µs

IA800 SPEZIFIKATIONEN

Dämpfungsfaktor (8 ohm): > 350:1 @ 20 Hz - 1 kHz

Eingangs CMRR:

> -65 dB @ 1 kHz

Spannungs Gain:

x40 (32 dB) Standard, x20 (26 dB) intern per Jumper wählbar

Eingangs-empfindlichkeit (x40):

1.22Volt @ 4 Ohm, 1.41 Volt @ 8

Ohm

Eingangsempfindlichkeit (X20):

2.5Volt @ 4 Ohm, 2.83 Volt @ 8 Ohm

Eingangs-impedanz:

20 k Ohm, balanciert

Brummen und rauschen:

>-110 dB, “A” gewichtet, bezogen auf angegebene Leistung

Nebensprechen:

>-65 dB, “A” gewichtet, bezogen auf angegebene Leistung

Stromaufnahme @ 1/8 Leistung:

950 Watt @ 4 Ohm, 725 Watt @

8 Ohm

Stromaufnahme @ 1/3 Leistung:

1,750 Watt @ 4 Ohm, 1,150 Watt

@ 8 Ohm

Stromaufnahme im leerlauf:

32 Watt im Standby Modus

Max. Stromaufnahme:

2,670 Watt @ 4 Ohm (zeitbegrenzt durch Stromkreisunterbrecher), 1,725 Watt @ 8 Ohm

Wärmeabgabe:

4,603 @ 1/3 Leistung 4 Ohm, 3,012 @ 1/3 Leistung 8 Ohm

Kühlung

120mm DC Lüfter, ausgeschaltet bis Kühlkörper 45oC erreicht, dann vari- able Geschwindigkeit

Regler:

2 rückseitige Dämpfer, sequentielles Ein-/Ausschalten

Anzeige-LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Schutz,

1 Leistungs-LED

Schutz:

2 Clip, 2 Signal, 2 LFC, 1 Schutz,

1 Leistungs-LED

Anschlüsse:

8-Pin Signal-Eingang (steckbar),

4-Pin seq. Einschaltfolge (steckbar),

4-Pol Klemmleiste, IEC AC Netzanschluss-Buchse

Konstruktion:

18 ga. stahlverstärkt mit 12 ga. Anschlußlaschen, extrudiertes Aluminium-Frontpanel

Abmessungen:

133mm x 483mm x 416.6mm (401mm hinter Anschlußlaschen)

Brutto-Gewicht:

(23.3 kg)

Netto-Gewicht:

(20.41 kg)

®

TM

Da wir ständig um Verbesserungen bemüht sind, unterliegen die hier aufgelisteten Features und Spezifikationen Änderungen ohne

vorheriger Ankündigung.

64

Image 64
Contents Series Power Amplifiers Precautions Table of Contents Amplifier Configuration Installation and MountingTo SET UP the Amplifier for Basic Usage IntroductionFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Signal Ground Connection Protection FeaturesSequential TURN-ON/TURN-OFF Wiring Sequential TURN-ON/TURN-OFFWire Gauge Chart AWGIA 200 Specifications IA 200V Specifications IA 400 Specifications Rated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005%Gross Weight 33.6 lbs .25 kg Net Weight Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input CmrrIA 400V Specifications IA 800 Specifications Rated Power 2 X 8 ohmsGross Weight 51.4 lbs .3 kg Net Weight THD 1 X 8 ohms 0.005% @ 425W @ 1 kHzIA 800V Specifications Current Draw @ 1/8 power IA 800V-70 765 wattsCurrent Draw @ 1/3 power IA 800V-70 1,100 watts Minimum Load Impedance IA 800V-70 12.5 ohmsImportant Safety Instructions Configuración DEL Amplificador Configuración DEL Amplificador Para LA Utilización BásicaIntroducción DesembalajePage Características Delpanel Frontal Características Delpanel Posterior Operación Configuración DEL Modo DE Señal Conexiones DEL Módulo DE EntradaPuentes DE Selección DE Ganancia Conexiones DE Salida DE AltavocesCompartimiento DE Control DE Amplificadores Desmontaje DE MódulosFunciones DE Protección Limitador DE RecorteProtección Térmica CortocircuitosPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Mínima impedancia de carga IA 200V-70 50 W Distorsión armónica total dos canales amplificadosDistorsión armónica total un canal amplificado Distorsión por intermodulación según norma SmptePotencia nominal 2 x 4 W Potencia nominal 2 x 8 WDistorsión armónica total 2 x 4 W Distorsión armónica total 2 x 8 WConsumo máximo de corriente IA Peso neto 14,06 kg% a 600 W desde 20 Hz hasta KHz con señal en ambos canales % 60 Hz y 7 kHz, 600 W a 4 WA 4 W, 1,41 V a 8 W A 4 W, 2,83 V a 8 WDisipación térmica BTU/h IA Ancho de banda de potencia IAPeso neto 20,41 kg Instrucciones DE Seguridad Importantes ¡GUARDE Estas InstruccionesConfiguration DES Amplificateurs InstallationIntroduction ’OUVERTURELED Signal Face Avant Pattes DE Montage EN RackSélecteur DE Mise Sous Tension Trois Positions LED D’ALIMENTATIONFace Arriere Modules D’ENTREE ET DE Communication Module D’ENTRÉEBornier DE Sortie CommunicationsUtilisation Emplacement Pour Module Cavaliers DE Selection DE GainConnexions DES HAUT-PARLEURS Manipulation D’UN ModuleConnexion DE LA Masse DU Signal Load Fault Correction Correction DE Faute DE ChargeEnlever OU Remplacer UN Module ProtectionsCOURT-CIRCUIT Protection Tension ContinueSequence TURN-ON/TURN-OFF Connexions TURN-ON/TURN-OFF SéquentielTable DE Section DES Câbles Caractéristiques IA Rated Ppwer 1 x 4 ohmsSlew Rate -25V/µs Damping Factor 8 ohms Max. Current DrawMaximum RMS Voltage Swing Minimum Load Impedance IA 200V-70 50 ohmsTHD one channel driven IA 05% @ 200W from 20 Hz KHz with both channels driven Watts @ 4 ohms, 1,010 watts @ OhmsMax Current Draw Indicator LEDs Watts @ 1/3 power IA 472 @ 1/3 powerVoltage Gain Cooling X40 32 dB standard, x20 26 dBRated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hr Damping Factor 8 ohms Rated Power 2 x 8 ohmsRated Power 1 x 4 ohms Controls Frequency Response Input Impedance Connectors15% @ 400W from 20 Hz to KHz with both channels driven IA Max Current DrawImportant Safety Instructions Installation UND Montage SET UP FÜR DEN Einfachen GebrauchEinführung AuspackenFront Panel Features Chassis FÜR DIE Rackmontage AC Netzschalter MIT 3 PositionenLED-ANZEIGE SCHUTZ-LEDAnschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULE EINGANGS-MODULELS Anschlussleiste KommunikationsschachtBetrieb Gain Select Jumper Signal Mode KonfigurationLautsprecher Ausgänge Signal ERDUNGS-VERBINDUNG Verstärker SteuerschachtModul Entfernen Entfernen Oder Austauschen Eines ModulesDC Spannungsschutz ÜberhitzungsschutzEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen IA 400V Spezifikationen LeistungsbandbreiteEingangs Cmrr NettogewichtIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation