Peavey IA 200V, IA 400V IA 800V Specifications, Minimum Load Impedance IA 800V-70 12.5 ohms

IA™ 800V SPECIFICATIONS

Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (one channel):

415 watts @ 1 kHz at < 0.01% THD

Minimum Load Impedance: IA 800V-70: 12.5 ohms

IA 800V-100: 25 ohms

Maximum RMS Voltage Swing: IA 800V-70: 85 volts

IA 800V-100: 110 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

IA 800V-70:

10 Hz - 100 kHz; +0, -3 dB at rated power

IA 800V-100:

10 Hz - 50 kHz; +0, -3 dB at rated power

THD (two channels driven): IA 800V-70:

<0.15% @ 400W from 20 Hz - 20 kHz with both channels driven

IA 800V-100:

<0.1% @ 400W from 20 Hz - 20 kHz with both channels driven

THD (one channel driven):

<0.008% @ 400W @ 1 kHz

SMPTE IMD:

< 0.1% 60 Hz and 7 kHz, @ 400W

Slew Rate:

35V/µs

Damping Factor:

> 400:1 @ 20 Hz - 400 Hz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally-jumper selectable

Input Sensitivity:

IA 800V-70:

1.77volts or 3.54 volts for rated output

IA 800V-100:

2.5volts or 5 volts for rated output

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-108 dB, “A” weighted referenced to rated power

Crosstalk:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power: IA 800V-70: 765 watts

IA 800V-100: 775 watts

Current Draw @ 1/3 power: IA 800V-70: 1,100 watts

IA 800V-100: 1,150 watts

Idle Current Draw:

45 watts in Standby Mode

Maximum Current Draw:

IA 800V-70:

1,680 watts for rated power IA 800V-100:

1,700 watts for rated power

Thermal Emissions (BTU/hr.):

IA 800V-70:

2,841 watts @ 1/3 power IA 800V-100:

3,015 watts @ 1/3 power

Cooling:

120mm DC fan, off until heatsinks reach 45oC, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

5.25" x 19" x 16.4" (15.8" behind rear mounting ears)

133mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight: 51.4 lbs. (23.3 kg.)

Net Weight:

45 lbs. (20.41 kg.)

®

TM

Due to our efforts for constant improvements,

features and specifications listed herein are subject to change without notice.

18