Peavey IA 800V, IA 200V, IA 400V, IA Series 05% @ 200W from 20 Hz KHz with both channels driven

Page 47

CARACTÉRISTIQUES IA 400

Rated Power (2 x 4 ohms):

300 watts @ 20 Hz - 20 kHz, both channels driven at < 0.1% THD

Rated Power (2 x 8 ohms): 200 watts @ 20 Hz - 20 kHz at < 0.05% THD

Rated Power (1 x 4 ohms):

360 watts @ 1 kHz at < 0.015% THD

Rated Power (1 x 8 ohms):

275 watts @ 1 kHz at < 0.005% THD

Minimum Load Impedance: 4 ohms

Maximum RMS Voltage Swing: 57 volts

Frequency Response:

10 Hz - 25 kHz; +0, -3 dB at 1 watt

Power Bandwidth:

10 Hz - 100 kHz; +0, -3 dB at rated power

THD (2 x 4 ohms):

<0.1% @ 300W from 20 Hz - 20 kHz with both channels driven

THD (2 x 8 ohms):

<0.05% @ 200W from 20 Hz -

20 kHz with both channels driven

THD (1 x 4 ohms):

< 0.01% @ 350W @ 1 kHz

THD (1 x 8 ohms):

< 0.005% @ 275W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 7 kHz, 300W @

4 ohms

Slew Rate: 30V/µs

Damping Factor (8 ohms): > 450:1 @ 20 Hz - 1 kHz

Input CMRR:

> -65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB) standard, x20 (26 dB) internally jumper-selectable

Input Sensitivity (x40):

.866 volts @ 4 ohms, 1 volts @

8 ohms

Input Sensitivity (x20):

1.73volts @ 4 ohms, 2 volts @ 8 ohms

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-108 dB, “A” weighted referenced to rated power @ 8 ohms

Crosstalk:

>-75 dB, “A” weighted referenced to rated power @ 8 ohms

Current Draw @ 1/8 power:

670 watts @ 4 ohms, 460 watts @

8 ohms

Current Draw @ 1/3 power:

1,055 watts @ 4 ohms, 650 watts @

8 ohms

Idle Current Draw:

30 watts in Standby Mode

Max. Current Draw:

1,622 watts @ 4 ohms, 1,010 watts @

8 ohms

Thermal Emissions (BTU/hr.): 2,915 @ 1/3 power 4 ohms, 1,591 @ 1/3 power 8 ohms

Cooling:

80mm DC fan, off until heatsinks reach 45° C, then variable speed

Controls:

2 rear panel attenuators, sequential turn on/off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

18 ga. steel reinforced with 12 ga. rack ears, extruded aluminum front panel

Dimensions:

3.48" x 19" x 16.4" (15.8" behind rear mounting ears)

88.4mm x 483mm x 416.6mm (401mm behind rear mounting ears)

Gross Weight: 33.6 lbs. (15.25 kg)

Net Weight:

30.2 lbs. (13.7 kg)

®

TM

Etant donnés nos efforts constants pour l’amélioration de notre matériel,

les caractéristiques et spécifications listée ici peuvent être modifiées sans préavis.

47

Image 47
Contents Series Power Amplifiers Precautions Table of Contents Introduction Amplifier ConfigurationInstallation and Mounting To SET UP the Amplifier for Basic UsageFront Panel Features Back Panel Features Operation Stereo Mode Connection Diagram Parallel Mode Diagram Module Removal Protection Features Signal Ground ConnectionSequential TURN-ON/TURN-OFF Sequential TURN-ON/TURN-OFF WiringAWG Wire Gauge ChartIA 200 Specifications IA 200V Specifications Damping Factor 8 ohms 4501 @ 20 Hz 1 kHz Input Cmrr IA 400 SpecificationsRated Power 1 x 8 ohms 275 watts @ 1 kHz at 0.005% Gross Weight 33.6 lbs .25 kg Net WeightIA 400V Specifications THD 1 X 8 ohms 0.005% @ 425W @ 1 kHz IA 800 SpecificationsRated Power 2 X 8 ohms Gross Weight 51.4 lbs .3 kg Net WeightMinimum Load Impedance IA 800V-70 12.5 ohms IA 800V SpecificationsCurrent Draw @ 1/8 power IA 800V-70 765 watts Current Draw @ 1/3 power IA 800V-70 1,100 wattsImportant Safety Instructions Desembalaje Configuración DEL AmplificadorConfiguración DEL Amplificador Para LA Utilización Básica IntroducciónPage Características Delpanel Frontal Características Delpanel Posterior Operación Conexiones DEL Módulo DE Entrada Configuración DEL Modo DE SeñalDesmontaje DE Módulos Puentes DE Selección DE GananciaConexiones DE Salida DE Altavoces Compartimiento DE Control DE AmplificadoresCortocircuitos Funciones DE ProtecciónLimitador DE Recorte Protección TérmicaPage Tabla DE Calibres DE Cables Especificaciones DEL Amplificador IA Distorsión por intermodulación según norma Smpte Mínima impedancia de carga IA 200V-70 50 WDistorsión armónica total dos canales amplificados Distorsión armónica total un canal amplificadoDistorsión armónica total 2 x 8 W Potencia nominal 2 x 4 WPotencia nominal 2 x 8 W Distorsión armónica total 2 x 4 WPeso neto 14,06 kg Consumo máximo de corriente IAA 4 W, 2,83 V a 8 W % a 600 W desde 20 Hz hasta KHz con señal en ambos canales% 60 Hz y 7 kHz, 600 W a 4 W A 4 W, 1,41 V a 8 WPeso neto 20,41 kg Ancho de banda de potencia IADisipación térmica BTU/h IA ¡GUARDE Estas Instrucciones Instrucciones DE Seguridad Importantes’OUVERTURE Configuration DES AmplificateursInstallation IntroductionLED D’ALIMENTATION LED SignalFace Avant Pattes DE Montage EN Rack Sélecteur DE Mise Sous Tension Trois PositionsCommunications Face Arriere Modules D’ENTREE ET DE CommunicationModule D’ENTRÉE Bornier DE SortieUtilisation Manipulation D’UN Module Emplacement Pour ModuleCavaliers DE Selection DE Gain Connexions DES HAUT-PARLEURSProtections Connexion DE LA Masse DU SignalLoad Fault Correction Correction DE Faute DE Charge Enlever OU Remplacer UN ModuleConnexions TURN-ON/TURN-OFF Séquentiel COURT-CIRCUITProtection Tension Continue Sequence TURN-ON/TURN-OFFTable DE Section DES Câbles Max. Current Draw Caractéristiques IARated Ppwer 1 x 4 ohms Slew Rate -25V/µs Damping Factor 8 ohmsTHD one channel driven IA Minimum Load Impedance IA 200V-70 50 ohmsMaximum RMS Voltage Swing Watts @ 4 ohms, 1,010 watts @ Ohms 05% @ 200W from 20 Hz KHz with both channels drivenX40 32 dB standard, x20 26 dB Max Current Draw Indicator LEDsWatts @ 1/3 power IA 472 @ 1/3 power Voltage Gain CoolingFrequency Response Input Impedance Connectors Rated Power 2 x 4 ohms Slew Rate Thermal Emissions BTU/hrDamping Factor 8 ohms Rated Power 2 x 8 ohms Rated Power 1 x 4 ohms ControlsMax Current Draw 15% @ 400W from 20 Hz to KHz with both channels driven IAImportant Safety Instructions Auspacken Installation UND MontageSET UP FÜR DEN Einfachen Gebrauch EinführungSCHUTZ-LED Front Panel Features Chassis FÜR DIE RackmontageAC Netzschalter MIT 3 Positionen LED-ANZEIGEKommunikationsschacht Anschlussfeld Rückseite EINGANGS- UND KOMMUNIKATIONS-MODULEEINGANGS-MODULE LS AnschlussleisteBetrieb Lautsprecher Ausgänge Signal Mode KonfigurationGain Select Jumper Entfernen Oder Austauschen Eines Modules Signal ERDUNGS-VERBINDUNGVerstärker Steuerschacht Modul EntfernenEIN- / Ausschaltfolge Sequentielles EIN- / Ausschalten ÜberhitzungsschutzDC Spannungsschutz Leiter Querschnittstabelle IA 200 Spezifikationen IA 200V Spezifikationen IA 400 Spezifikationen Nettogewicht IA 400V SpezifikationenLeistungsbandbreite Eingangs CmrrIA 800 Spezifikationen IA 800V Spezifikationen Wichtige Sicherheitsrichtlinien Peavey ONE-YEAR Limited WARRANTY/REMEDY Product of Peavey Electronics Corporation