Seagate DL585 manual NIC Bbwce

Page 4

	BBWC assembly	44
	SCSI backplane	45
	System battery	46
	System board	48
	AC filter cable assembly	50
	Re-entering the server serial number	53
4	Diagnostic tools
5	Server component identification
	Connectors	56
	Rear panel	56
	SCSI backplane	57
	DIMM slots	58
	Processor and PPM	58
	LEDs	59
	Front panel	59
	QuickFind diagnostic display	60
	Hot-plug SCSI hard drives	61
	Hot-plug SAS or SATA hard drives	63
	Hot-plug fans	65
	Hot-plug power supplies	65
	NIC	66
	BBWCE	67
	Internal diagnostic display	68
	System board switches	69
	System maintenance switch (SW3)	69
	System ID switch (SW4)	70
	iLO/Redundant ROM override switch (SW5)	71
	Non-maskable interrupt switch	72
	Rear unit identification LED switch	72
6	Troubleshooting
	If the server does not start	74
	Diagnostic steps	75
	Problems after initial boot	80
	Troubleshooting a failed processor	82
	Two-processor memory board configuration	82
	Four-processor memory board configuration	82
	Other information resources	83
Specifications
	Server specifications	84
Index

Contents 4

Image 4

Contents HP ProLiant DL585 Server Page Contents NIC Bbwce Where to go for additional help About this guideAudience assumptions Technician notesIntegrated Management Log Telephone numbersIllustrated parts catalog Customer self-repair programMechanical components spare parts list Mechanical components exploded view‡REQUIREMENT System components spare parts list System components exploded viewPPM Sdram ‡REQUIREMENT Removal and replacement procedures Safety considerationsPreparation procedures Electrostatic dischargePowering down the server Locating and removing the Torx T-15 tool Extending the server from the rackRemoval and replacement procedures Removing the access panel Installing the access panelRemoving the server from the rack Processor memory boards Processor memory board population guidelinesPPM Processor Removing a processorRemoval and replacement procedures Memory options Minimum memory requirementsRemoving a Dimm Hard drive blanks Drive replacement precautionsHot-plug Scsi hard drives Hot-plug SAS or Sata hard drives SAS or Sata hard drive cage Power transfer board Removal and replacement procedures Power supply blank Hot-plug power supplies Hot-plug fans Universal media drivesRemoving a drive from bay Front bezel Power button/LED assembly Expansion boards Performance balancing PCI-X expansion boardsScsi cables Front fan cage Pass-through board QuickFind diagnostic display board and lightpipe Rear fan cage Bbwc assembly Scsi backplane System battery Locating the battery on the system boardRemove the existing battery System board Removal and replacement procedures AC filter cable assembly Cutting the cable tie-wrapsRemoval and replacement procedures Removal and replacement procedures Re-entering the server serial number Diagnostic tools Diagnostic toolsPost Server component identification ConnectorsRear panel Scsi backplane board connectors Scsi backplaneDimm slots Processor and PPMLEDs Front panelQuickFind diagnostic display HP ProLiant DL585 Server User Guide onHot-plug Scsi hard drives Hot-plug Scsi hard drive LEDsHot-plug Scsi hard drive LED combinations Hot-plug SAS or Sata hard drives Hot-plug SAS or Sata hard drive LED combinationsHot-plug SAS or Sata hard drive LED combinations Hot-plug power supplies Hot-plug fansNIC Bbwce Internal diagnostic display System board switches System maintenance switch SW3System ID switch SW4 System ID switch SW4 System ID Switch SW4ILO/Redundant ROM override switch SW5 Non-maskable interrupt switch Rear unit identification LED switchTroubleshooting If the server does not start Diagnostic steps Is the system power LED off?Is the internal health LED green? Servers Troubleshooting Guide Is the monitor displaying information? Error message Problems after initial boot Provided in the Factory-Installed Two-processor memory board configuration Troubleshooting a failed processorFour-processor memory board configuration Other information resources Specifications Server specificationsIndex UID LED