Seagate DL585 manual Hot-plug Scsi hard drive LED combinations

Page 62

Table 14	Hot-plug SCSI hard drive LEDs
Item	Description	Status

3	Fault status	On = Drive failure
		Flashing = Fault-process activity
		Off = No fault-process activity

Table 15 Hot-plug SCSI hard drive LED combinations

Activity LED	Online LED	Fault LED	Status

On	Off	Off	Do not remove the drive. Removing a drive during this process will
			cause data loss.
			The drive is being accessed and is not configured as part of an
			array.

On	Flashing	Off	Do not remove the drive. Removing a drive during this process will
			cause data loss.
			The drive is rebuilding or undergoing capacity expansion.

Flashing	Flashing	Flashing	Do not remove the drive. Removing a drive during this process will
			cause data loss.
			The drive is part of an array being selected by the Array
			Configuration Utility, or the Options ROMPaq is upgrading the drive.

Off	Off	Off	OK to replace the drive online if a predictive failure alert is received
			and the drive is attached to an array controller.
			The drive is not configured as part of an array.
			-Or-
			If this drive is part of an array, then a powered-on controller is not
			accessing the drive.
			-Or-
			The drive is configured as an online spare.

Off	Off	On	OK to replace the drive online.
			The drive has failed and has been placed offline.

Off	On	Off	OK to replace the drive online if a predictive failure alert is received,
			provided that the array is configured for fault tolerance and all other
			drives in the array are online.
			The drive is online and configured as part of an array.

On or flashing	On	Off	Do not remove the drive. Removing a drive during this process will
			cause data loss.
			The drive is online and being accessed.

Server component identification 62

Image 62

Contents HP ProLiant DL585 Server Page Contents NIC Bbwce Audience assumptions Where to go for additional helpAbout this guide Technician notesIntegrated Management Log Telephone numbersIllustrated parts catalog Customer self-repair programMechanical components spare parts list Mechanical components exploded view‡REQUIREMENT System components spare parts list System components exploded viewPPM Sdram ‡REQUIREMENT Preparation procedures Removal and replacement proceduresSafety considerations Electrostatic dischargePowering down the server Locating and removing the Torx T-15 tool Extending the server from the rackRemoval and replacement procedures Removing the access panel Installing the access panelRemoving the server from the rack Processor memory boards Processor memory board population guidelinesPPM Processor Removing a processorRemoval and replacement procedures Memory options Minimum memory requirementsRemoving a Dimm Hot-plug Scsi hard drives Drive replacement precautionsHard drive blanks Hot-plug SAS or Sata hard drives SAS or Sata hard drive cage Power transfer board Removal and replacement procedures Power supply blank Hot-plug power supplies Hot-plug fans Universal media drivesRemoving a drive from bay Front bezel Power button/LED assembly Expansion boards Performance balancing PCI-X expansion boardsScsi cables Front fan cage Pass-through board QuickFind diagnostic display board and lightpipe Rear fan cage Bbwc assembly Scsi backplane System battery Locating the battery on the system boardRemove the existing battery System board Removal and replacement procedures AC filter cable assembly Cutting the cable tie-wrapsRemoval and replacement procedures Removal and replacement procedures Re-entering the server serial number Diagnostic tools Diagnostic toolsPost Rear panel ConnectorsServer component identification Scsi backplane board connectors Scsi backplaneDimm slots Processor and PPM LEDs Front panelQuickFind diagnostic display HP ProLiant DL585 Server User Guide onHot-plug Scsi hard drives Hot-plug Scsi hard drive LEDsHot-plug Scsi hard drive LED combinations Hot-plug SAS or Sata hard drives Hot-plug SAS or Sata hard drive LED combinationsHot-plug SAS or Sata hard drive LED combinations Hot-plug power supplies Hot-plug fansNIC Bbwce Internal diagnostic display System board switches System maintenance switch SW3System ID switch SW4 System ID switch SW4 System ID Switch SW4ILO/Redundant ROM override switch SW5 Non-maskable interrupt switch Rear unit identification LED switchTroubleshooting If the server does not start Diagnostic steps Is the system power LED off?Is the internal health LED green? Servers Troubleshooting Guide Is the monitor displaying information? Error message Problems after initial boot Provided in the Factory-Installed Four-processor memory board configuration Troubleshooting a failed processorTwo-processor memory board configuration Other information resources Specifications Server specificationsIndex UID LED