Seagate DL585 manual QuickFind diagnostic display board and lightpipe

Page 42

QuickFind diagnostic display board and lightpipe

To remove the QuickFind diagnostic display board and lightpipe:

1.Power down the server. See “Powering down the server” earlier in this chapter.

2.Extend the server from the rack. See “Extending the server from the rack” earlier in this chapter.

3.Remove the access panel. See “Removing the access panel” earlier in this chapter.

4.Remove the processor memory boards. See “Processor memory boards” earlier in this chapter.

5.Remove the PCI-X expansion boards. See “PCI-X expansion boards” earlier in this chapter.

6.Remove the SCSI cables. See “SCSI cables” earlier in this chapter.

7.Remove the front fan cage. See “Front fan cage” earlier in this chapter.

8.Remove the pass-through board. See “Pass-through board” earlier in this chapter.

9.Eject all devices from the universal media drive bays. See “Universal media drives” earlier in this chapter.

10.Unplug the Power button/LED cable. See “Power button/LED assembly” earlier in this chapter.

11.Loosen the two thumbscrews holding the diagnostic display board.

12.Slide the board to the rear of the unit until it stops, and then lift it up.

Figure 38 Removing the QuickFind diagnostic display board and lightpipe

13.Lift the board out gently, being careful of the universal media drive bay connector. Reverse the steps to replace the diagnostic display board and lightpipe.

Removal and replacement procedures 42

Image 42

Contents HP ProLiant DL585 Server Page Contents NIC Bbwce Audience assumptions Where to go for additional helpAbout this guide Technician notesIntegrated Management Log Telephone numbersIllustrated parts catalog Customer self-repair programMechanical components spare parts list Mechanical components exploded view‡REQUIREMENT System components spare parts list System components exploded viewPPM Sdram ‡REQUIREMENT Preparation procedures Removal and replacement proceduresSafety considerations Electrostatic dischargePowering down the server Locating and removing the Torx T-15 tool Extending the server from the rackRemoval and replacement procedures Removing the access panel Installing the access panelRemoving the server from the rack Processor memory boards Processor memory board population guidelinesPPM Processor Removing a processorRemoval and replacement procedures Memory options Minimum memory requirementsRemoving a Dimm Drive replacement precautions Hard drive blanksHot-plug Scsi hard drives Hot-plug SAS or Sata hard drives SAS or Sata hard drive cage Power transfer board Removal and replacement procedures Power supply blank Hot-plug power supplies Hot-plug fans Universal media drivesRemoving a drive from bay Front bezel Power button/LED assembly Expansion boards Performance balancing PCI-X expansion boards Scsi cables Front fan cage Pass-through board QuickFind diagnostic display board and lightpipe Rear fan cage Bbwc assembly Scsi backplane System battery Locating the battery on the system boardRemove the existing battery System board Removal and replacement procedures AC filter cable assembly Cutting the cable tie-wrapsRemoval and replacement procedures Removal and replacement procedures Re-entering the server serial number Diagnostic tools Diagnostic toolsPost Connectors Server component identificationRear panel Scsi backplane board connectors Scsi backplaneDimm slots Processor and PPMLEDs Front panelQuickFind diagnostic display HP ProLiant DL585 Server User Guide onHot-plug Scsi hard drives Hot-plug Scsi hard drive LEDsHot-plug Scsi hard drive LED combinations Hot-plug SAS or Sata hard drives Hot-plug SAS or Sata hard drive LED combinationsHot-plug SAS or Sata hard drive LED combinations Hot-plug power supplies Hot-plug fansNIC Bbwce Internal diagnostic display System board switches System maintenance switch SW3System ID switch SW4 System ID switch SW4 System ID Switch SW4ILO/Redundant ROM override switch SW5 Non-maskable interrupt switch Rear unit identification LED switchTroubleshooting If the server does not start Diagnostic steps Is the system power LED off?Is the internal health LED green? Servers Troubleshooting Guide Is the monitor displaying information? Error message Problems after initial boot Provided in the Factory-Installed Troubleshooting a failed processor Two-processor memory board configurationFour-processor memory board configuration Other information resources Specifications Server specificationsIndex UID LED