Lantronix DSTni-EX Interrupt Flags, Note The reset value of this register’s bits is indeterminate

Page 80

Interrupt Flags

The following flags are set on internal events (they activate an interrupt line when enabled). They are cleared by writing a ‘ 1’ to the appropriate flag. Acknowledging the tx_msg interrupt also acknowledges all tx_xmit interrupt sources. Acknowledging one of the tx_xmit interrupt sources also acknowledges the tx_msg interrupt.

Note: The reset value of this register’s bits is indeterminate.

Table 5-36. Interrupt Flags

BIT

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

OFFSET

46h

FIELD

_XMIT2TX

_XMIT1TX

_XMIT0TX

_CRCERR

FORMERR

_ACKERR

STUFERR

OVRLOAD

ARBLOSS

_MSGRX

_MSGTX

_BUSOFF

_ERRBIT

_OVRRX

///

RESET

−

−

−

−

−

−

−

−

−

−

−

−

−

−

−

−

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

			Table 5-37. Interrupt Flag Definitions

	Bits	Field Name		Description
	15	RX_MSG		Rx Message
				Depending on rx_level, at least one message is available.
	14	TX_MSG		Tx Message
				Depending on rx_level, at least one message is empty.
	13	TX_XMIT2		Tx Xmit 2
				Indicates that the message was successfully sent.
	12	TX_XMIT1		Tx Xmit 1
				Indicates that the message was successfully sent.
	11	TX_XMIT0		Tx Xmit 0
				Indicates that the message was successfully sent.
	10	BUS_OFF		Bus Off State
				CAN has reached the bus off state.
	9	CRC_ERR		CRC Error
				CRC error occurred while sending or receiving a message.
	8	FORM_ERR		Format Error
				Format error occurred while sending or receiving a
				message.
	7	ACK_ERR		Acknowledgement Error
				Acknowledgement error occurred while sending or receiving
				a message.
	6	STUF_ERR		Stuffing Error
				Stuffing error occurred while sending or receiving a
				message.
	5	BIT_ERR		Bit Error
				Bit error occurred while sending or receiving a message.
	4	RX_OVR		Receiver Overrun
				A new message arrived while the receive buffer is full. This
				Flag is set if either the incoming message overwrites an
				existing one or is discarded.
	3	OVR_LOAD		Overload Condition
				An overload condition has occurred.
	2	ARB_LOSS		Arbitration Loss
				Arbitration was lost while sending a message.
	1:0	///		Reserved

72

Image 80

Contents DSTni-EX User Guide Section FivePage Copyright & Trademark LantronixTechnical Support Master DistributorWarranty Contents 1 About This User Guide2 SPI Controller 3 I2C ControllerList of Tables 5 CAN ControllersTable 3-17. Clock Control Register List of Figures 1 About This User Guide Intended Audience ConventionsNavigating Online Notes Notes are information requiring attentionOrganization 2 SPI Controller Theory of OperationSPI Background DSTni SPI ControllerSPI Controller Register Summary Table 2-1. SPI Controller Register SummarySPI Controller Register Definitions SPIDATA RegisterRESET Table 2-2. SPIDATA RegisterCTL Register Interrupt Request EnablePhase Select Wire-OSPISTAT Register Table 2-6. SPISTAT RegisterTable 2-7. SPISTAT Register Definitions Interrupt RequestSPISSEL Register Table 2-10. BCNT Bit SettingsSelectO Signal Table 2-8. SPISSEL RegisterDVDCNTRLO Register DVDCNTRHITable 2-11. DVDCNTRLO Register Table 2-12. DVDCNTRLO Register DefinitionsFeatures 3 I2C ControllerFigure 3-1. DSTni I2C Controller Block Diagram Block DiagramI2C Background Master Transmit Mode I2C ControllerOperating Modes Table 3-1. Master Transmit Status Codes CodeI2C State Microprocessor ResponseServicing the Interrupt Table 3-2. Codes After Servicing Interrupts Master TransmitTransmitting Each Data Byte Table 3-3. Status Codes After Each Data Byte TransmitsAll Bytes Transmit Completely Master Receive ModeTable 3-4. Master Receive Status Codes Table 3-5. Codes After Servicing Interrupt Master Receive Slave Transmit Mode Receiving Each Data ByteTable 3-6. Codes After Receiving Each Data Byte Slave Receive Mode Bus Clock Considerations Bus Clock SpeedClock Synchronization Bus ArbitrationProgrammer’s Reference I2C Controller Register SummaryResetting the I2C Controller Table 3-7. I 2C Controller Register SummaryI2C Controller Register Definitions Slave Address RegisterGeneral Call Address Enable Table 3-8. Slave Address RegisterData Register Table 3-10. Data RegisterControl Register Table 3-12. Control RegisterTable 3-13. Control Register Definitions Extended Slave AddressStatus Register Table 3-14. Status RegisterStatus Code Table 3-15. Status Register DefinitionsTable 3-16. Status Codes Table 3-18. Clock Control Register Definitions Clock Control RegisterTable 3-17. Clock Control Register Software Reset Register Extended Slave Address RegisterTable 3-21. Software Reset Register Table 3-22. Software Reset Register Definitions4 USB Controller USB Background USB InterruptUSB Core Serial Interface EngineUSB Hardware/Software Interface Digital Phase Lock Loop LogicMicroprocessor Interface Buffer Descriptor TableFigure 4-1. Buffer Descriptor Table Rx vs. Tx as a Target Device or HostTable 4-1. USB Data Direction Addressing BDT EntriesTable 4-2. 16-Bit USB Address Table 4-3. 16-Bit USB Address DefinitionsTable 4-4. BDT Data Used by USB Controller and Microprocessor USB Controller Determines…Microprocessor Determines… Table 4-5. USB Buffer Descriptor FormatTable 4-6. USB Buffer Descriptor Format Definitions BD OwnerDATA0/1 Transmit or Receive USB OwnershipUSB Transaction Figure 4-2. USB Token TransactionDedicated to host mode USB Register SummaryTable 4-7. USB Register Summary USB Register Definitions Interrupt Status RegisterTable 4-8. Interrupt Status Register Table 4-9. 16- Interrupt Status Register DefinitionsEnable/Disable USBRST Interrupt Sleep TimerError Condition USB ResetTable 4-11. 16- Error Interrupt Status Register Definitions Error RegisterTable 4-10. Error Interrupt Status Register Error interrupt with two functions Data Field Received Not 8 BitsCRC16 Failure PID check field failedLive USB Differential Receiver JSTATE Signal Live USB Single Ended Zero SignalTable 4-12. Status Register Table 4-13. Status Register DefinitionsUSB Reset Signal Host Mode Enable valid for host mode onlyResume Signaling BDT PDD ResetTable 4-15. 16- Address Register Definitions Address RegisterTable 4-14. Address Register Frame Number Registers Table 4-16. Frame Number RegisterTable 4-17. Frame Number Register Definitions Frame NumberToken Register Endpoint for Token Command Table 4-18. Token RegisterTable 4-19. Token Register Definitions Table 4-20. Valid PID TokensEndpoint Control Registers Endpoint EnableTable 4-21. Endpoint Control Registers Table 4-22. Endpoint Control Register DefinitionsHost Mode Operation Table 4-23. Endpoint Control Register DefinitionsSample Host Mode Operations Figure 3. Enable Host Mode and Configure a Target DeviceFigure 4. Full-Speed Bulk Data Transfers to a Target Device USB Pull-up/Pull-down Resistors Figure 4-5. Pull-up/Pull-down USBUSB Interface Signals USB Output EnableHOST Mode Enable Clock CLK5 CAN Controllers Data Exchanges and Communication Arbitration and Error CheckingCANBUS Background CANBUS Speed and Length Table 5-1. Bit Rates for Different Cable LengthsCAN Register Summaries Register SummaryHex Offset RegisterHex Offset Detailed CAN Register Map Table 5-4. Detailed CAN Register MapAcceptance Filter Enable Register Hex OffsetRegister CAN Register Definitions TX Message RegistersFigure 5-1. TX Message Routing Sending a MessageTx Message Registers Table 5-5. TxMessage0ID28Table 5-6. TxMessage0ID12 Table 5-7. TxMessage0DataTable 5-12. TxMessage0Ctrl Flags Table 5-13. TxMessage0 Register DefinitionsMessage Identifier for Both Standard and Extended Messages Message DataRX Message Registers Figure 5-2. RX Message RoutingRx Message Registers Table 5-14. RxMessageID28Table 5-15. Rx Message ID28 Register Definitions Table 5-16. RxMessageID12Table 5-20. Rx Message Data Table 5-21. Rx Message Data 39 Register DefinitionsTable 5-22. Rx Message Data Table 5-23. Rx Message Data 23 Register DefinitionsTable 5-26. RxMessage RTR Table 5-27. Rx Message RTR Register DefinitionsTable 5-28. Rx Message Msg Flags Table 5-29. Rx Message Msg Flags Register DefinitionsError Count and Status Registers Table 5-30. Tx/Rx Error CountTable 5-31. Tx\Rx Error Count Register Definitions Table 5-32. Error StatusTable 5-34. Tx/Rx Message Level Register Table 5-35. Tx/Rx Message Level Register Definitionsrxlevel10 txlevel10Interrupt Flags Note The reset value of this register’s bits is indeterminateCRC Error Format ErrorInterrupt Enable Registers Table 5-38. Interrupt Enable RegistersTable 5-39. Interrupt Enable Register Definitions Bus Off State − int2n group error interruptsCAN Operating Mode Table 5-40. Interrupt Enable RegistersTable 5-41. Interrupt Enable Register Definitions Overload Condition − int3n group diagnostic interruptsCAN Configuration Registers Configuration Bit RateFigure 5-3. CAN Operating Mode Table 5-42. Bit Rate Divisor RegisterTable 5-44. Configuration Register Table 5-45. Configuration Register DefinitionsOverwrite Last Message CfgsjwBit Time tseg1 +tseg2 + time quanta TQAcceptance Filter and Acceptance Code Mask Table 5-46. Acceptance Filter Enable RegisterTable 5-47. Acceptance Filter Enable Register Definitions Table 5-48. Acceptance Mask 0 RegisterTable 5-50. Acceptance Mask Register ID Table 5-51. Acceptance Mask Register ID12 DefinitionsTable 5-52. Acceptance Mask Register Data D5556Table 5-54. Acceptance Code Register Table 5-55. Acceptance Code Register DefinitionsTable 5-56. Acceptance Mask Register ID12 Table 5-57. Acceptance Mask Register ID12 DefinitionsCANbus Analysis Arbitration Lost Capture RegisterTable 5-60. Arbitration Lost Capture Register Table 5-61. Arbitration Lost Capture Register DefinitionsError Capture Register Table 5-62. Error Capture RegisterTable 5-63. Error Capture Register Definitions ErrorcodeTable 5-65. Error Capture Register Definitions Frame Reference RegisterTable 5-64. Frame Reference Register Stuff Bit InsertedCAN Bus Interface Interface ConnectionsFigure 5-6. CAN Connector Figure 5-5. CAN Bus InterfaceFigure 5-7. Power for CAN +5CANGNDCAN +24VFigure 5-8. CAN Transceiver and Isolation Circuits 0.01uf